Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Long 2610 hydraulic problem


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Jeff in Kansas on June 07, 2007 at 12:46:23 from (64.219.133.131):

I recently bought a Long 2610 with a loader at an auction. I tried out the 3 pt lift and loader before I bought it and they both seemed to work fine(without anything attached to the 3-point arms). I got the tractor home and hooked up a chisel to the 3 point arms. The tractor would pick up the chisel at first but then after a few minutes in the up position, if i tried to lower the chisel and then lift it again, it would not pick it back up no matter how high I revved the engine.

After some investigation, I noticed that the hydraulic pump would get hot enough that you could not keep your hand on it if the chisel was left in the up position, but if I move the 3-point control lever forward about 1/4 th of the quadrant the pump will cool down (and the chisel at this lever position has not yet started to go down). After the oil cools off everything will work fine if I raise the chisel by pulling the lever all the way back, and after the chisel has been raised, back off the lever to the position noted above and the chisel will remain in the raised position. Also noticed that when I move the lever past that 3/4 raised point of the quadrant with the chisel attached(I have not tried it without the chisel attached) I can hear the engine work a little harder.

So what is happening is when I raise an implement and leave the lever in the fully raised position, the pump and oil will get hot and the lift will not work. The loader has no such problems, so I am thinking that there may be an adjustment or something in the hydraulic lift?

Anyone have any suggestions?



Replies:




Add a Reply

:
:
:

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - History of the Nuffield Tractor - by Anthony West. The Nuffield tractor story started in early 1945. The British government still reeling from the effects of the war on the economy, approached the Nuffield organization to see if they would design and build an "ALL NEW" British built wheeled tractor, suitable for both British and world farming. ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy