Posted by Billy NY on March 11, 2013 at 10:34:11 from (72.226.79.200):
In Reply to: Ford 4000 brakes posted by boat tractor on March 10, 2013 at 20:56:43:
Seeing the oil bath brake type was covered, I'll take a stab at the drum type, just in case, as I don't know the other type except obviously how to distinguish the difference between the 2 LOL !
If you have a these, they are fairly typical drum type brakes, with all the springs, adjuster, pads, drum etc.
My drum brakes make a little noise on occasion, I did do a complete brake job, all new parts on this tractor. They are relatively simple, a few odds and ends to consider, one side has one less spring, the end of the linkage, (I'll call it an actuating cam) does wear and may need to be built up to operate correctly, mine were worn and it made a difference in the pedal where it contacts the frame of the pad, easily observed when apart on the right side, push the pedal down. If you build them up too much, the drum won't go on, I recall a little "finesse" to get that right.
There is bearing and axle seal on the end of the axle, these can leak and soak the brake pad, glaze or what have you, not sure if that would create noise, our 3600 has the same style brakes as my 850 and it also has leaking seals and the brakes did make a little noise. The hitch with the repair is getting the bearing out out, I have not done this repair, but most seem to find a way to crack, cut or what have you the bearing cage, remove and somehow press the new one back in, don't quote me, something along those lines, its been posted many times on the Ford forum.
I do know that the OEM drums are of better material, I did get new drums made in Turkey, thicker cast material but I did split one, likely horsing it when one side got stuck, under normal use they are ok I think as I got quite a few years out of them before that one cracked, I put the oem one back on.
Might just be an adjustment, best to pull the wheel and drum to see what is going on, wear, check for the seal leaking etc.
In any event, hopefully some help if you have this type.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Choosin, Mounting and Using a Bush Hog Type Mower - by Francis Robinson. Looking around at my new neighbors, most of whom are city raised and have recently acquired their first mini-farms of five to fifteen acres and also from reading questions ask at various discussion sites on the web it is frighteningly apparent that a great many guys (and a few gals) are learning by trial and error and mostly error how to use a very dangerous piece of farm equipment. It is also very apparent that these folks are getting a lot of very poor and often very dangerous advice fro
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.