Posted by John_PA on May 15, 2012 at 05:17:03 from (96.236.165.64):
I am about to buy 2 grain bins. I wanted some advice before I buy them.
Both bins are 21.5' diameter(from what he said, I didn't actually measure them yet) and 8 rings high. I think the rings are 32 inches. One bin has a propane dryer, drying floor with steel supports under it, a top sweep, a center stirring auger, a clean sweep, 6 inch unloading auger, safety ring on roof, ladders inside and out.
The other bin has a drying floor and a 7.5 hp fan, 6 inch unloading auger, safety ring on roof, and ladders inside and out... No stirring auger or any of that.
I can't find anyone with bin jacks, or anyone willing to tear down and reassemble these bins. The only guy I could find willing to do it was from out in Ohio and he wanted $11,400 to take them both down and reassemble and I would have to pay extra for the concrete. He also said he couldn't get to them until november. I found jacks online for $8100.
I really don't want to spend that much as I could buy a new bin for that much with free installation.
How strong are the roofs on these bins? how much do they weigh? I might be able to get a 65 foot, 12 ton crane truck with operator for a few hundred bucks for a weekend. I was thinking that maybe, if the roof was strong enough, and the bin was light enough, I could lift it through the top hole, and unbolt the top 2 rings with the roof, lower it to the ground, then unbolt the roof, then lift it back up, bolt the roof to the next ring, take 2 more off... repeat as necessary... Once the rings are on the ground 2 at a time, I think it would be easy to get them apart sheet by sheet.
Someone told me I could lift the whole bin up by the roof, unbolt the bottom 2 rings, tear apart, then lower the bin, unbolt the next 2 rings, and so on. Is the roof really strong enough to support the whole weight of a 21 foot diameter bin, 21 feet tall? I was also told that the whole thing didn't weigh more than a couple thousand pounds. Are they really that light?
If anyone has any ideas, I would love to hear them. Also, if anyone in the lower 48 states has any grain bins for sale fitting the above description, that are already torn down, I might be interested in buying them.
Also... the bins look mildly rusty, they are from 1986, GSI brand, and the guy wants $3000 each, including all the fans and drying equipment. Sounds like a good price for this area, any thoughts?
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - The Nuts and Bolts of Fasteners - Part 2 - by Curtis Von Fange. In our previous article we discussed capscrews, bolts, and nuts along with their relative hardness and thread sizes. In this segment we will finish up on our fasteners and then work with ways to keep them from loosening up in the field. Capscrews, bolts and nuts are not the only means of holding two parts together. When dealing with thinner metals like sheet tin, a long bolt and
... [Read Article]
Latest Ad:
Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
