Posted by John_PA on January 13, 2012 at 01:37:27 from (72.95.148.249):
I bought a POWCON welder, made by Cyclomatic in San Diego, CA. It is a brute and a beast. It's a 300sm and it does stick, mig and tig. It's great!
Here's the problem...
I am not an electrician and do not claim to be one. I know enough to do most anything, but never went to school. I can wire 3 phase and I can do 3 way switches in single phase. etc etc... wiring does not scare me. I know how it goes. It is not hard to learn. I know what gauge wire to use for an application, and can figure out amp requirements for a circuit...
Regardless, I am not an electrician...
I buy this welder and I assume the guy knows his stuff. I figured he wired teh plug on the welder, because red was cut off flush, green/black/white was hanign long. He directly wired it to his 200 amp service. he put a white and black on the two hots, and the green on the neutral.
Now, I assume he wired it to the welder. He didn't. It's welding on 110v and not doing a good job, so I beg of him to stop and let me look. he stops, reverses the green for the white and tries again. welds slow and nothing is workign fine, so I tol him to stop, I'd buy the welder and just to stop. He does. So I bring it home, open it up, and low and behold...
BTW, I got it for a steal of a price.
It's wired for 230v/440v single-three... there are buss bars. the buss bars are in teh 230v position, but the ground green is obviously to a groudning post, red-white-black go to a junction and they seem to be in order. red and black are both wired to a hot jumper and the white(neutral) is the voltage coming back. The red lead from teh plug is cut short, they never hooked it up.
So, I put red to a hot, black to a hot on a 50 amp breaker, white to neutral and green to the grounding block. The welder runs decent but I can tell it has some troubles. I take it to my welding shop, they open it up and say, "some idiot reversed the ground and hot when they wired it."
$320 later, after components, it welds fine.
Moral of the story...
If you are not an electrician, please don't guess or pretend to be one. Even more-so, if I tell you I think you are wrong, don't judge or second guess me, but listen to me and let me teach you. If not, I will forever imagine your shoe when I am shooting the bottom of a urinal. You make me unhappy, you guesser of things you don't understand. I am not an expert, but I know... it makes me mad not to have the confidence to proclaim my righteousness in your presence.
I'm just saying...
Hope someone, someday will let up and let me speak without judging me.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - The Nuts and Bolts of Fasteners - Part 2 - by Curtis Von Fange. In our previous article we discussed capscrews, bolts, and nuts along with their relative hardness and thread sizes. In this segment we will finish up on our fasteners and then work with ways to keep them from loosening up in the field. Capscrews, bolts and nuts are not the only means of holding two parts together. When dealing with thinner metals like sheet tin, a long bolt and
... [Read Article]
Latest Ad:
Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
