Posted by Fixerupper on July 27, 2011 at 17:06:40 from (207.199.205.239):
Most of you guys, including me, who have worked on old tractors have been through this situation before but I have to vent about this one.
A friend asked me if I'd put the mag back on his 48 JD B. I said 'sure, why not! I'm kind of busy trying to get this military vehicle done but throwing a mag on will take fifteen minutes so I can come over after supper and do it.
A little history on this B, it's one he picked up maybe 6 or 7 years ago. It'd been well cared for as a whole but a little worn. I got it running for him including going through the carb. It idled smoother than any B I have ever seen.
So, back to the story. I get to the tractor, pull #1 plug, stick my finger in the hole turn it over and there's no compression. Stuck valve! So I timed it by bringin #2 up on compression. Put the mag on. Battery was a little low so we pulled it to start it but #2 piston hydraulic locked. Shut off the gas, pulled the plug wires off the mag, opened the petcocks, pulled it and gas flew up out of the muffler and down through the petcock. Took the carb off and it was mighty rusty. Now my little 15 minute job that I wasn't too wild about in the first place was getting long. Took the carb apart. Bowl was full of rust and the float had gas in it. Took the carb home and pulled it apart. Put the body and bowl in the electrolysis tank while I run up to Roberts Carb for gaskets, float and needle and seat. Got it back together after a quick blowing out, went back to the tractor. Pulled the valve cover and had to use my slide puller to get #1 exhaust valve to pop back out. Put valve cover back on, throw the carb back on, open the petcocks and out comes ANTIFREEZE!!!! Remember, folks, I didn't want to do this in the first place!!!!! Pull started it but it doesn't idle well, so there's something down in the idle passage. Gassy oil was coming out the fan shaft so the crankcase is just a little overfull huh? Told him to try black pepper in the rad. Left and went home to the project that wasn't getting done while I was trying to revive a dead horse. GRRRR. Jim
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - The Nuts and Bolts of Fasteners - Part 2 - by Curtis Von Fange. In our previous article we discussed capscrews, bolts, and nuts along with their relative hardness and thread sizes. In this segment we will finish up on our fasteners and then work with ways to keep them from loosening up in the field. Capscrews, bolts and nuts are not the only means of holding two parts together. When dealing with thinner metals like sheet tin, a long bolt and
... [Read Article]
Latest Ad:
Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
