Owen Aaland said: (quoted from post at 00:12:48 12/21/14) How are you engaging the starter? If you are just jumping across the from the battery cable stud to the starter motor terminal all you are doing is running the motor without the solenoid pulling the drive gear into the flywheel.
Yup could be a few things so start with the cheapest.
1. make sure that you are arcing the right two posts.
2. you may need to remove the dust cover to see if the starter is still engaged in the flex plate turn the toque converter/crank a little to try and loosen the Bendix gear. You can use the large bolt on the Harmonic crank balancer.
2.5 go to the store and buy a pack of band-aids finger wrap type, you'll need them. :wink: :wink: :D
3. Disconnect the battery :the bolt - Is it two or three bolt starter cone?
3.5 Jackstands...
Either way you are going to need a 24" extension and a wobbly joint to get the top bolt. The two bolt, you'll get it from the back and the three bolt you'll go in from the front. Both ways you will need all your savvy to weave that long extension past the exhaust or through the motor mount past the gas lines.
From the factory chevy has a 7/16 nut on the back side of the starter to support the front of the starter, I would say that 99.999999% of them have been removed due to the fact they are a bugger to get back on. Once the bolts are out remove the battery cable from the starter.
Newer Chevy' have two knurled shank bolts going up though the bottom of the starter, sometimes this type needed shims to hold it away from the flex-plate ring gear. THIS TYPE OF STARTER WAS DOOMED FROM THE BEGINNING DUE TO HEAT OFF THE EXHAUST. FYI > If you can slip a thin sheet of aluminum between the exhaust and starter you can double the life of the starter.
4. Don't drop the starter on your fingers or your face, and if you do at least you have band-aids ;)
5. a bad valve cover gasket can drip enough oil on the starter to make it do funky things even flames. Oil can get in and ground out the solenoid contacts, brushes and/or armature. Also if the starter is oil flooded when it cools down it drags even more.
That's it for now
Good luck
This post was edited by Fatamus at 01:11:04 12/21/14.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - The Rescue of a Fordson F - by Anthony West. Introduction I live in the UK and have for many years restored Fordson tractors (in the main model N's). I have also restored and shown model F's, E 27N's, Field Marshall Series 2, David Brown Cropmasters and the old rey Fergeson T 20. At one time I had seven restored examples which were shown and used in ploughing matches. As most restorers, I have a number of war stories I can relate on a range of topics that may help other like minded and interested people. Perhaps my first p
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
