First on most H's or M's there are 3 marks on that pulley. The mark all by itself when aligned with the pointer allows one to grease the pilot bearing from underneath the tractor. That is all it is used for.
Of the 2 marks together: think of that 2nd mark as only a visual indicator only in most cases and at minimum it keeps you from confusing it with that other stand alone mark which you would easily do if it were not there. If you have a distributor in your tractor then no chance you will use that 2nd mark for anything other than as a visual indicator. If you have a magneto then I guess you could use that 2nd mark but it likely depends on the procedure you are following. The IT manual does not use that 2nd mark. But I have heard of people purposely retarding the timing a bit if you plan to hand crank so you do not get a broken arm from engine kickback if timed too aggressively.
The first mark of the 2 marks that are close together is #1 cylinder at TDC.
If you plan to time your tractor without the engine running then these are all the marks that you need and you can follow IT manual procedure or IH static procedure accordingly.
Unfortunately, if you want to time your engine running then you will need to account for the advance in the distributor (if you have a distributor) by adding you own timing mark with either a white paint pen or liquid paper whiteout correction fluid that typists use works too.
To do this you need to some math and have a flexible tape measure that you can use to follow the perimeter circumference of the pulley.
Most H's have a crank pulley that measures 6.5 inches in diameter.
For a desired 40 degrees setting on a Farmall h: measure 2.269 inches (or 2 and 9/32 inches) by following the perimeter of the pulley with a flexible tape measure in the advanced direction from TDC mark and add your mark with a paint pen. Use a timing light and align with your mark with engine running.
For your own custom degree calculation on a Farmall h which you may need to do if you have high compression pistons then use the following formula:
6.5 x 3.1415 x (your desired degree) / 360 = value in inches from TDC mark for you to place your mark
Most M's have a crank pulley that measures 7.49 inches in diameter.
For 22 degrees on a Farmall M: 1.438 inches (or 1 and 7/16 inches) advanced from TDC mark make your mark with paint pen.
For 30 degrees on a Farmall M: 1.960 inches (or 2 inches).
For 40 degrees on a Farmall M: 2.614 iches (or 2 and 5/8 inches).
For your own custom degree setting on a Farmall M use this formula which you may need to do if you have high comprssion pistons:
7.49 x 3.1415 x (your desired degree setting) / 360 = value in inches for you to place your mark.
Note1: Timing should be done at Wide Open throttle on the Farmalls when using a timing light.
Note2: Ideally it is a good idea to verify your wide open throttle setting is close with a tachometer (I use a hand handheld and measure off the PTO shaft to set both idle and WOT governor settings). At unloaded WOT on a Farmall H or M you should be close to 600 rpm on PTO shaft.
Some Farmall M specs
Low idle: Engine - 425; PTO - 158
Rated speed: 1450; PTO 540
High idle: 1595; PTO 594
This post was edited by rankrank1 at 17:47:58 12/14/13 8 times.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Box Plow Blues - by Tom Schwarz. One of the first implements most tractor owners obtain is the box plow. For very little money, this piece of equipment promises to plow and flatten any hill or vale on your ranch road or farm. At least that's what I thought! As simple as a box plow appears, it can be rather challenging to make work correctly. In our sandy soils of Florida, traction is king. You can never have wide enough tires or heavy enough weights to get all the traction you want … unless you own a monster tractor. U
... [Read Article]
Latest Ad:
Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
