Posted by Janicholson on December 08, 2013 at 14:00:16 from (74.60.94.18):
In Reply to: 1086 Windshield posted by onyx on December 08, 2013 at 13:13:31:
The rope trick: I will share. Needed: 1/8" nylon or poly cord (no thicker) Silicon Spray Warmth 65 or more degrees is desirable Put the rubber gasket on the glass (if it has a split in it (one long universal piece) wrap it on and measure it with no stretching, and cut it to length, then super glue the ends together, (not on the glass)) When the gasket is on the glass, wrap one and 1/2 gasket lengths of the cord into the outer groove of the gasket such that the beginning and end of the cord are at the bottom of the glass, and using a bit of tape, held there. Spray the outer groove with silicone spray (wet is OK) Place the window onto the bottom metal edge such that the gasket is in place on both sides of the metal edge. This will also require care so the gasket is centered in the opening left to right. While pushing firmly on the glass to hold it against the edge, pull on the tail end of the cord. when you get to the lip of the gasket that is outside the edge, the cord will act like a tire tool pulling the lip inside the edge. Continue around the frame being careful to seat the gasket as the cord is pulled. As you progress to the top of the frame, the opposite end of the cord can also be pulled to start the gasket lip up the other side. Push in at all times to avoid loosing the fit, or position of the glass. Hold both ends of the cord when or if it begins to slip through the gasket, Slipping can cut the gasket, and loosing the end of the cord is not good. The last couple of inches will be the hardest, pull so the cord is not trying to cut into the gasket, rotating the position of the cord and tugging may be an answer. I replaced 40 rear windows in brand new F150 250 Pu trucks using this method. (putting in slider windows in place of solid glass) It is the best I have to offer. Jim
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Tractor Profile: Allis-Chalmers Model G - by Staff. The first Allis-Chalmers Model G was produced in 1948 in Gasden, Alabama, and was designed for vegetable gardeners, small farms and landscape businesses. It is a small compact tractor that came with a complete line of implements especially tailored for its unique design. It featured a rear-mounted Continental N62 four-cylinder engine with a 2-3/8 x 3-1/2 inch bore and stroke. The rear-mounted engine provided traction for the rear wheels while at the same time gave the tractor operator a gre
... [Read Article]
Latest Ad:
Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
