Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Super M cam gear successfully replaced


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Bob M on October 16, 2000 at 08:53:59 from (192.232.120.194):

Followup to my post a couple weeks ago - this tractor had the nut unscrew off off the camshaft, letting the cam gear gradually flop itself to death inside the timing gearcase...

Got the new cam gear installed this weekend. My idea to secure the key in the damaged keyway with JB Weld did not work (just like T_Bone predicted...) - the key popped out 1st time I tried to fit the gear into place. However I found by using a new Woodruff key, the new gear has a nice force fit on the camshaft - it drives the camshaft solidly even before installing the cam nut. Put on a new nut keeper, treated the threads with blue Loctite, then torqued the cam nut to 150 ft-lb. When I got all done the camshaft had 0.010 endplay - exactly per spec - and the cam gear ran true when cranked.

Put the gear cover back on, then test ran the engine. It started right up, ran nice and that annoying knock is GONE!. Found also the low idle speed has increased by 100+ RPM - probably due to the valve timing now being back where it should be. Only let it run a minute (no radiator or coolant yet) but am satisfied with the repair.

Next up is to reinstall the front end and radiator assembly - this weekend weather permitting.

Thanks to all who offered advice and support!

Bob M



Follow Ups:




Post A Followup

:
:

: Re: Super M cam gear successfully replaced

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Niagra View Mobile - Powered by a 1959 Ford Tractor - by Mark Massey. In 1959 the Niagara Frontier Transit Inc. of Buffalo, New York designed and built six Viewmobiles for the Niagara Frontier Sightseeing Inc. for use as a sightseeing ride at the Niagara Falls State Park, Niagara Falls, New York, powered by a 1959 Ford 611 Tractor. ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy