Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Brakes on H


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by sgtbull on December 15, 2011 at 16:41:58 from (163.191.228.254):

In Reply to: Brakes on H posted by dcpky on December 15, 2011 at 16:11:47:

Once the bolt and washer are off, the brake drum should slide straight off. Its not a tapered shaft, so it is most likely stuck w/ a little rust or just crud. If your seals are leaking, its even less likely to be rust. A pair of prybars, carefully applied on opposiste sides, will usually pop the drum off. If that fails, reinsert just the bolt and use a two jaw puller.. carefully.
The seal can then be pried out by driving a sharped old srewdriver (a big'un) through the side of the seal and prying it carefully, but firmly. You'll totally destroy the seal, but don't worry, you're replacing it anyway. Just be careful not to damage the shaft or the seal housing.
DON'T take the cap screws out thinking you're going to remove the entire housing. It won't come out unless you're inside the tranny and have takent the bull gears loose. If anything, make sure they're good and tight.
New seals are much thinner than the old ones, and you CAN double up on them, but the newer seals are so much better, one seems to be adequate. Just try to position it to a depth wehre it doesn't run in any groove worn by the previous leather seal on the brake drum. Make sure you put a dab of oil/grease on the portion of the drum that goes into the seal so you don't accidently fold the lip of the seal back and knock the spring off.
Good luck! Its not a difficult task, and is time well spent.
BTW, if your brake bands are just oil soaked, but otherwise not in bad shape, you can burn the oil off w/ a torch (outside, away from flammables), as the bands should be fireproof. They can be reused then.
Do ONE side at a time or be very careful to not get parts swapped from one side to the other. The actuators are side specific.


Replies:




Add a Reply

:
:
:

:

:

:

:

:

:

Advanced Posting Options

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.



 
Advanced Posting Tools
  Upload Photo  Select Gallery Photo  Attach Serial # List 
Return to Post 

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Niagra View Mobile - Powered by a 1959 Ford Tractor - by Mark Massey. In 1959 the Niagara Frontier Transit Inc. of Buffalo, New York designed and built six Viewmobiles for the Niagara Frontier Sightseeing Inc. for use as a sightseeing ride at the Niagara Falls State Park, Niagara Falls, New York, powered by a 1959 Ford 611 Tractor. ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy