Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: m farmall electrical system


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Tom Harrower on July 29, 2000 at 10:34:46 from (216.126.190.194):

In Reply to: m farmall electrical system posted by ray king on July 29, 2000 at 08:40:08:

Hi Ray, I could be wrong, but I have read that the one wire delco 10si alternator is used mainly for marine applications, where it would run at a moderately high rpm for a length of time, and has only one wire. In order for it to start charging, it has to be ran at higher rpm than what most tractor applications would comfortably do. The 10 si alternator in the diagram is called a three wire alternator, but for most tractor applications there are only two wires that actually leave the alternator. The exception would be if you had an unusually long distance to run your wiring, then the " third " wire is the one that runs from one of the slide terminals on the alt, to the batt post on the back of the alt. as a jumper. If your wiring was running a long distance, that third wire would connect to a source that was far away from the alternator, such as the ampmeter or a junction block, to assist the alternator in allowing more voltage to be produced to compensate for the voltage drop or resistance in the extra length of the wiring. As said, someone please correct me if I am wrong, I have read much on this conversion and that is how I understood it to be.As for your regulator and other wiring: the 10 si delco alternator has its own voltage regulator built in to it, any other regulator should be removed along with the wiring connected to it. Save it though if it is the original 6 volt as you may want to restore your 6volt system down the road. Wire your tractor as per the diagram. If you have lights, wire them off the ampmeter to a good 12 volt switch, and make sure to use a fuse. That is the down side to doing this 12 volt conversion, you have to remove all the original neat looking factory stuff, but if you do a neat job it will look ,as well as work good. Hope this helps, Tom


Follow Ups:




Post A Followup

:
:

: Re: Re: m farmall electrical system

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Ford N-Series Transmission/Hydraulic Fluid - The Full Story - by Llamas. The transmission fluid in an “N”:-series tractor lubricates the transmission, differential, rear wheel bearings, PTO and hydraulic pump drive, and it also cats as the working fluid for the hydraulic lift. In 9N/2N models, it also lubricates the steering sector and shaft system. The owner’s manual for the 9N and 2N models specified the use of only two fluids. They were STRAIGHT MINERAL OIL SAE 90 (above freezing) and ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy