Posted by AG in IN on April 18, 2011 at 16:32:32 from (67.236.85.111):
In Reply to: Tisco Carb Kit posted by J.L. Every on April 18, 2011 at 06:32:19:
Quoting Removed, click Modern View to see
The last Tisco tune-up kit I bought for an IH distributor on an M I had to bend/twist the points quite a bit to get them to align squarely. Might have been just the kit I bought, I don't know. I've have had better luck with Tisco kits for D-R distributors.
The last A&I kit I bought the rotor was junk. You could slide the contact piece around about 1/4 inch.
The last "genuine" CIH ignition parts I bought the cap woudn't even come close to fitting properly. They must have changed suppliers or something about a year ago.
All imported condensers seem to be of questionable quality. Some work fine, some make your points look like you welded on them after 5 hours, some just quit. I try to reuse my old condensers if the points look fairly decent for the hours that are on them.
Lately I've been buying NAPA/Echlin ignition parts. Pricey, but they fit and hold up well. I have also had good luck with Standard and Blue Point ignition parts in the past, too.
Years ago, nearby TSC or QFF stores stocked "Standardized" ignition parts in a bubble pack. The other had "Sorensen" ignition parts. Both were good bang for your buck.
Quoting Removed, click Modern View to see
The holes in some of the aftermarket bowl gaskets are usually a bit off. Make sure you use good packing for the main fuel adjustment screw if it isn't in the kit. When you get the carb apart, make sure you shake your float to be sure it doesn't have a hole in it. Check for throttle shaft bushing wear too.
Some folks curse the rubber-tipped needle seats, but I think they're in the CIH kits, too. The rubber-tipped ones stick once in a while and the old style steel ones can seep.
Always check dimensions of the main nozzle before swapping it out if it's in the kit. I can't speak for Tisco's kits, but A&I's nozzles are sometimes wrong. Compare all shafts, butterflies, etc., to your old ones.
Don't toss any old parts until you are happy with the way your tractor runs with the new parts in the carb.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Talk of the Town: Repairin a Gas Tank - by Staff. This interesting discussion is from the Tool Talk Discussion Forum. Remember that safety is your first priority - make sure you know what you are doing before attempting a potentially dangerous activity!
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
