Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Cub belt. ARRRRGH


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Mark W. on July 17, 2000 at 10:53:06 from (209.6.106.197):

In Reply to: Cub belt. ARRRRGH posted by Louise on July 16, 2000 at 08:59:31:

Louise:

I'll try to keep this as short as I can.

Possibilites to check are pulley alignment, belt tension, and foreign objects.

If you had the wrong pulley it may have caused an alignment problem. If you buy the new one, be sure the "protrusion" faces the right way if you have an assembly drawing. If you don't have a drawing, install the pulley to optimize its alignment with the other pulley(s) with the deck in the mowing position. If it still looks cockeyed you may have a bent spindle or some other warped/broken part (not likely), or an extremely bad bearing (unlikely to be that bad).

Be sure the belt is neither too tight (not likely) nor too loose (possible).

As for foreign objects, here's what happened to me. It's a long shot but it may apply in your case: A small piece of stick broke off and lodged unnoticed in a groove on one of the pulleys. The next thing I knew, the belt broke (it was about 2 years old). I put on a new belt and it broke within two hours. I traced the problem to the little piece of wood, which was worn smooth and had created a small (maybe 3/16") bump in the pulley groove. Each time the pulley revolved the bump would wiggle the belt just enough that the outside of the belt (where its strength is) rubbed on a belt guide. It didn't take long for the outside of the belt to fray enough for the belt to break. I popped the wood off the pulley with a small screwdriver and have had no problems since.

So, check your pulley grooves for stuff that shouldn't be there. If the pulleys you still have are O.K. it may be worth a walk in the weeds to check the one that flew off. Try to avoid finding it the hard way (with the bush hog)!

Good luck - -

Mark W.




Follow Ups:




Post A Followup

:
:

: Re: Re: Cub belt. ARRRRGH

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Ford N-Series Transmission/Hydraulic Fluid - The Full Story - by Llamas. The transmission fluid in an “N”:-series tractor lubricates the transmission, differential, rear wheel bearings, PTO and hydraulic pump drive, and it also cats as the working fluid for the hydraulic lift. In 9N/2N models, it also lubricates the steering sector and shaft system. The owner’s manual for the 9N and 2N models specified the use of only two fluids. They were STRAIGHT MINERAL OIL SAE 90 (above freezing) and ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy