Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Re: Farmall Super A with frozen engine


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Ralph Kramden on July 08, 2000 at 01:08:59 from (209.239.201.100):

In Reply to: Re: Farmall Super A with frozen engine posted by Ralph Kramden on July 06, 2000 at 22:40:51:

Wellll, I was walking past the tractor and it pulled me in like a giant vacuum cleaner! I had NO choice! It told me to take off work today and see just what the problem was.
So, I tried, with no luck, several methods of turning the engine over after removing the starter motor. First, I tried prying a little more than gently, but not much, with my largest screwdriver in the starter motor opening, then with a 5 ft. wrecking bar. Zip. So, I removed the front cover, radiator and fan assembly and was able to get to the front pulley. As luck would have it, the same bar fits nicely in the crank pulley, and I was able with the help of a pipe wrench on the pry bar to turn the engine over backwards a half turn. This told me the pistons weren't moving all the way around, so I removed the cylinder head and sure enough, there was considerable rust and crud in the no. 2 and 3 pistons. I am not sure of the numbering, but it was the middle 2 cylinders. So, after scraping, cleaning and honing, it now turns all the way over.
I am a little worried about cracks in the top of the engine block. Cracks start at the number 1 cylinder sleeve and run to the water holes by no.2, then to the sleeve in no.2, then to the water holes in no.3, then to the sleeve in no. 3, even weakening the wall a little at the sleeve. Do I need a new block? ( Shudder ). Are they even available?
Tomorrow ( after work, of course, heh heh ) I plan to talk with my local machinist about the cracks and see how much he'll grind the valves for, as long as the head is of.
The weird hitch ball turned out to be an actual ball hitch that somebody had inserted in place of a large bolt. Must've been all they had handy.
The loader does have, I discovered, a sticker saying International 1000. The other implements are for sure not factory. The scraper says " Ditch Maker". Must have been for making roads with ditches alongside? The sickle bar is from some German-sounding company. That bar looks like death eatin' onions. I wonder how many men those things have dis-whatevered.


Follow Ups:




Post A Followup

:
:

: Re: Re: Re: Farmall Super A with frozen engine

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Ford N-Series Transmission/Hydraulic Fluid - The Full Story - by Llamas. The transmission fluid in an “N”:-series tractor lubricates the transmission, differential, rear wheel bearings, PTO and hydraulic pump drive, and it also cats as the working fluid for the hydraulic lift. In 9N/2N models, it also lubricates the steering sector and shaft system. The owner’s manual for the 9N and 2N models specified the use of only two fluids. They were STRAIGHT MINERAL OIL SAE 90 (above freezing) and ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy