Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  

Re: 806 steering/mcv problems


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Owen Aaland on September 28, 2010 at 16:01:44 from (65.174.247.47):

In Reply to: 806 steering/mcv problems posted by farmalcrazy on September 26, 2010 at 17:17:22:

You have three problems, none of them critical, but combined will cause the symptoms you are having. The O-ring seal between the center section and the rear frame is leaking air into the hydraulic system suction side. It is located above the normal oil level in the transmission so it will leak air in rather than oil. Quick fix is to run the oil level about 5 or 6 gallons over full. That puts the oil level above the leaking O-ring so it will now draw in oil rather than air.

This problem is made worse by a worn MCV pump. A new pump is somewhat forgiving oh having to pump air but a worn one does a poor job causing the loss of hydraulics for the steering and controls.

The third problem is the sprag clutch is worn out in the low side of the TA. It most likely already slips under load. Without any hydraulic pressure to engage clutch packs in the TA all you are left with is the mechanical side of the low side clutch. Since it is worn out the tractor does not move when there is no hydraulic pressure.

First try adding the extra oil. If that is not enough to get you going, this is how you can bleed the air from the system. Remove the small plug on the back side of the MCV assembly. It is the one with the 5/8 inch head. Start the tractor and be ready to shut it off when oil shoots out. If you get no oil with the tractor idling you can apply some air pressure to the oil fill tube to assist in the bleeding.


Replies:




Add a Reply

:
:
: :

:

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


 
Advanced Posting Tools
  Upload Photo  Select Gallery Photo  Attach Serial # List 
Return to Post 

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Box Plow Blues - by Tom Schwarz. One of the first implements most tractor owners obtain is the box plow. For very little money, this piece of equipment promises to plow and flatten any hill or vale on your ranch road or farm. At least that's what I thought! As simple as a box plow appears, it can be rather challenging to make work correctly. In our sandy soils of Florida, traction is king. You can never have wide enough tires or heavy enough weights to get all the traction you want … unless you own a monster tractor. U ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy