Posted by Crazy Red Power in SE-WI on September 12, 2010 at 20:18:11 from (24.183.132.223):
I've been thinking, again, about IH's numbering system. There has to be something to it & I hope someone can fill me in. I'd like to begin with an excerpt from an email to Leroy. Goes a bit like this:
"The part number for that bearing does start with a "K". I am still a bit of a novice when it comes to understanding part numbers, but I think the "K" in the part number references Keystone as in Keystone rakes. They (IHC) either designed the bearing box around the Keystone bearing or that bearings' specs were what they needed for that application. If the letter K is followed by a second letter, the latter letter denotes a revision. There are plenty of other prefix letters in the book, as well. "PO" (Parlin & Orrendorf) is usually a number found on pins & hardware, "Q" I think means quota. If so, it would be a reference to the hardware a dealer should always have stock of. A few numbers begin with "M". I believe these are from the Milwaukee line. There's one part number in the book that doesn't fit in with the rest, a Zerk #14186DA. I think it's from the tractor or engine line. All the "R" & "RA" numbers would be for parts built after the initial 1902 merger or after 1913 when IHC was told they couldn't monopolize towns anymore. IHC would then begin to number all of their parts with prefixes related to the type of machine i.e. "M" for mowers, "R" for rakes, "P" for planters, etc. "PO" numbers remained with the plow line for the most part. In the 1950's they revised the number system."
An afterthought: There are plenty of other groups that have me thrown, though. All of the old part numbers for the stationary threshers end with "N". Most all of the parts for my grain drill start with "N". The corn binder is all "C"'s & "Q"'s.
What about the new numbering system (ex. 251 293 R91 or 876 567 C91)? "R" can be found all over the place, in parts catalogs for most anything. "C" pops up quite a bit in the truck line. Refrigeration has it's share of "S" & "SE". I only have an owners manual for Milkers, but "C" or "CA" are the only suffixes. My tractor manuals are full of "D", "DA" & "R". The "R" numbers seem to be from the newer renumbering. "ST" seems to indicate a standard bearing, but what about "M"?
Then there's the numbers, "R91", "R92", etc. These seem to be assemblys. Single digits after the suffix seem to be individual parts. What about an "R11" number? On rare occasion I run across this suffix. The parts are individual & either rubber or hardware. Is "R11" the new "Q" code? I'm also wondering about the first 6 digits of the new numbers. Are the first three digits group? If so, there dosen't seem to be too much consistancy. The next three numbers I haven't a clue about. Too random.
Well, these are the puzzle pieces I'm working with. Am I anywhere close to right? If someone could fill me in on how they did it with the part numbers, I'd be much obliged.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Choosin, Mounting and Using a Bush Hog Type Mower - by Francis Robinson. Looking around at my new neighbors, most of whom are city raised and have recently acquired their first mini-farms of five to fifteen acres and also from reading questions ask at various discussion sites on the web it is frighteningly apparent that a great many guys (and a few gals) are learning by trial and error and mostly error how to use a very dangerous piece of farm equipment. It is also very apparent that these folks are getting a lot of very poor and often very dangerous advice fro
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
