I spent 5 or 6 of my teenage years with my butt in the seat of Pappy's Cub, when he was running a custom mowing service. We used several different mowers under the Cub over the years, but the Woods 42 was the most versatile. With the Woods 42, you could cut stuff from lawns to weeds higher than the hood, and make it all look good as long as you kept the blades sharp...and with the quick-change blades, there's no excuse NOT to keep your blades sharp.
The Woods 59 was probably better on 2"-3" lawns, but it pulled harder than the 42...which is natural, since it's 40% bigger, not to mention you're driving 3 mower spindles and bearings instead of one. The Danco/IH 5-foot rotary pulled even harder than the Woods 59, although I never quite understood why. Best on lawns that were 3" or less--and COMPLETELY dry--was the Mott Hammerknife flail mower. It pulled harder than the 42, but when conditions were right, you could leave a lawn looking like a carpet.
As far as a Cub sickle bar mower, there were a couple of different lengths...4-1/2 feet and 5-foot cutter bars, IIRC. If the cutter bar is sharp,and the stuff you're cutting isn't wet, you should have no problems with it plugging up as long as you match your ground travel speed to what you're cutting. Or at least that's my experience. We used the sickle bar mower on the Cub when mowing street rights-of-way and alleys, and cutting around fire hydrants for the town. Advantage of the sickle bar mower is, you don't have to drive over the area you're cutting...such as a ditch bank.
If your Cub is down on power, the 5-foot mowers will let you know in a hurry; the 42 and the sickle bar, not as much. As for the gopher holes, many a Cub front spindle housing has been cracked or broken by dropping a front wheel into a gopher hole. That's why there are so many Cubs out there with welded spindle housings.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Tractor Profile: Allis-Chalmers Model G - by Staff. The first Allis-Chalmers Model G was produced in 1948 in Gasden, Alabama, and was designed for vegetable gardeners, small farms and landscape businesses. It is a small compact tractor that came with a complete line of implements especially tailored for its unique design. It featured a rear-mounted Continental N62 four-cylinder engine with a 2-3/8 x 3-1/2 inch bore and stroke. The rear-mounted engine provided traction for the rear wheels while at the same time gave the tractor operator a gre
... [Read Article]
Latest Ad:
Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
