Posted by Wardner on July 10, 2010 at 21:35:05 from (4.154.232.8):
In Reply to: Hey Wardner.... posted by Crazy Red Power in SE-WI on July 09, 2010 at 14:18:32:
OK, I am sold. I will have to try some malted frozen confections. I usually go with the quick and easy Ben and Jerry's pint.
Don't know the weight of the soda fountain. I have only handled it with the forklift. I imagine it could weigh 1500 lbs when full of product.
Power steering is in my plans. The Standard Treads use a drag link that is fitted with a hydraulic cylinder and integral spool valve. When the pitman arm moves, the appropriate internal port is opened and extends or retracts the piston. I have this IH system on both my 650 and 660 although they do not interchange. I have been looking for the W400-W450 system. I will probably buy an aftermarket unit. I have seen them priced at $350 and $500. I wonder if they will have enough push/pull to do the job. It is low priority at the moment. The units look easy to attach to any drag link type steering.
As for the wet bar, no thanks. That's a whole basket full of complications I can do without. But the LP tractor fuel could run a grill but that is years away. It would also mean I would be saddled with a payroll. Yuck.
I built a fast hitch for the back end of the tractor. It currently has a large military winch hanging off the back. That will come off and be replaced with something like a hot water tank heated by the engine through a heat exchanger. I have several SS tanks and heat exchangers.
Yes, the tractor will be heavy. It already has a 10 KW generator and a 15 HP air compressor running off the belt pulley. The front hitch parts probably add around 750 lbs.
The log splitter dies are just 2"x 3" chunks of steel cut from the legs of a pallet stacker. The wedge is a spring leaf from a heavy truck. It is way too sharp for a "top die". I insert a piece of 1/4" steel between the wedge and the work. It lasts about 15 bends before it is sheared and replaced.
This post was edited by Wardner at 21:41:30 07/10/10.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Choosin, Mounting and Using a Bush Hog Type Mower - by Francis Robinson. Looking around at my new neighbors, most of whom are city raised and have recently acquired their first mini-farms of five to fifteen acres and also from reading questions ask at various discussion sites on the web it is frighteningly apparent that a great many guys (and a few gals) are learning by trial and error and mostly error how to use a very dangerous piece of farm equipment. It is also very apparent that these folks are getting a lot of very poor and often very dangerous advice fro
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
