Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Farmall H stops when hot??


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by ScottyHOMEy on January 17, 2010 at 12:41:10 from (64.222.222.251):

In Reply to: Re: Farmall H stops when hot?? posted by kennebunksawmill on January 17, 2010 at 12:01:34:

This is all assuming you have a battery ignition and not a magneto.

The battery igntion, even on a 12v tractor, operates on 6v. So you will have one of two setups.

A) a resistor inline between your ignition switch and the coil. This reduces the input to the coil, which is wound internally to make your spark from a 6v input. In this case, a failure of the resistor will leave you with no input to the coil. Generally, in my experience with ballast resistors, it just fails, and stays failed. A bad coil often, but not always, will fail as it heats up, when a weak spot in the windings heats up and breaks continuity in the windings, breaking the circuit/field. In those cases, it will often close back up when it cools and run again until its heated back up. If you wire around the resistor, you'll be delivering a straight 12v to a 6v coil. It will take it, but it's hard in the long run on points and condensor. Okay for test purposes, but not general running.

B) In the absence of a resistor, you likely have the other type coil, which is made for a direct 12v input. It doesn't actually have a resistor built into it -- it is wound differently inside from the 6v variety, to produce the same spark.

If the tractor is showing the symptom of dying after ten minutes or so, but restarting and running fine after an hour or two to cool down, before dying again, I'm suspecting the coil. Someone else made the very good suggestion of checking for a spark from either the ignition wire from teh coil or one of the spark plugs ASAP when it shuts down. If no spark then, but an hour or two later, you can figure coil (especially if it is WICKED hot to the touch or seems to have been leaking oil or other stuff). If no spark later either, the condensor and coil could both be suspect.

As far as replacement coils, you have your choice. If you have a resistor, you can leave it in place and buy a 6v coil. You could also eliminate the resistor and buy a coil that takes a 12v input. If you have a 12v input type coil already, just replace it -- I don't see much point in adding a resistor and switching back to a 6v coil in that case.

Let us know how you make out!

27* down here in Waldo County today.


Replies:




Add a Reply

:
:
:

:

:

:

:

:

:

Advanced Posting Options

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.



 
Advanced Posting Tools
  Upload Photo  Select Gallery Photo  Attach Serial # List 
Return to Post 

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - New Life for an Old Allis - by Tyler Woods. My friend Jon, has an old '39 Allis Chalmers B. He thought it a marginal tractor that had long since served its time. She smoked terribly and never had much power but he couldn't afford another so he was limping along with what he had. Jon's Allis has a small front loader and though it doesn't carry much, it serves his needs. It was the hard starting and low power that made him think it was time to replace the old girl. Jon called me to help him discover why his tractor wouldn't start ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy