CaterpillarGuy: So, are you saying that the factory Remote Control valve is double-action? I don't know that I would have figured that out, as I've been pushing both rods forward to lower the 3-point hitch, which would have cut power to the Remote valve before it had a chance to engage its down circuit. I'll have to try leaving the main valve engaged and push forward on the Remote valve to see if it does, indeed, power down.
I have, however, tried raising the deck with the main lever hooked on that little peg in the 'up' position and just pulling back on the remote lever, but it doesn't work, the deck _falls_ an increment every time I pull the remote lever out. I need to have the main AND remote levers pulled ALL the way out to raise the deck, which is a pain while I'm moving because I have to use both hands on the levers and steer with my knees. Is there some sort of adjustment for them, or do I have bad or worn valves?
Wardner: Thanks for the info about the Select-o-Lift. I don't think I'd need one, I was just curious how it could be done. The book didn't mention needing a separate valve, so I wondered.
More questions for you all: If one were to want to use the Remote valve for something, but the Remote is dependent on the main for pressure, how would one use the Remote for an implement without also engaging the implement hooked to the main? I'm thinking, a 3-point hitch on the main and a front-end loader on the remote. If I have to engage the main to power the remote, the 3-point would have to be raised to then use the loader.
Speaking of double-action valves, is there such a thing as an aftermarket position control system? I'd love to have that for mowing, to be able to keep the deck out of the dirt without using a limiting strap or piston clamps. The remote does keep the deck partway up (presuming that's what does it), but it loses pressure while I'm mowing, so I occasionally have to raise it again or the mower starts biting the ground. It'd be one less thing to have to worry about.
One last set of questions (for now): How many here have an auxiliary valving system for their Ms, such as the lever shown in Jim's diagram? Where do you mount the levers, and what sorts of things do you use them for?
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Choosin, Mounting and Using a Bush Hog Type Mower - by Francis Robinson. Looking around at my new neighbors, most of whom are city raised and have recently acquired their first mini-farms of five to fifteen acres and also from reading questions ask at various discussion sites on the web it is frighteningly apparent that a great many guys (and a few gals) are learning by trial and error and mostly error how to use a very dangerous piece of farm equipment. It is also very apparent that these folks are getting a lot of very poor and often very dangerous advice fro
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
