Okay guys, laugh at me. I bought a 560 it had no lights, it had two 6 volt batteries mounted to the side of it instead of under teh hood for easier access I presume. It is a diesel so have to run the glow plugs about 90 seconds before I crank. They are those long narrow batteries hooked together in series which i guess is how I come up with 12 volts. I rewired all of the lights from the rotary switch, it has 4 positions, Off I presume, Dim, Bright and without Rear Light ( or maybe I hooked up something wrong - quite possible ) the lights all work and the generator has been changed to a GM alternator.
I just tested for continuity on the rotary light switch and then hooked up the lights accordingly. My 560 has square fenders like a 656 and I added two outside lights to those. I hooked up the fender lights to come on when the two lights come on that are on the pipe bars that come from the center console area like on your 400. It is the same rotary looking switch as we had on our 400 LPG that I grew up on.
I have no idea if our 400 was 12 or 6 volt all I can tell you is dad had a 12 volt battery under the seat. I do not recall seeing a large resistor or diode on it anywhere from jumping it many times over the years. It was a hard starter. The starter was notorious for sticking and you would have to put it in road gear and rock the tractor furiously to get it to disengage if you were lucky and did not have the blade or implement on the rear on the ground or the loader on the front dragging. Not sure if that had anything to do with the 6/12 volt issue.
Not sure if this helps a lot but there was an obvious hot wire for the switch and a ground. I just used jumper wires from the battery posts and a 12 volt test light to see what position on the switch lit up when I moved it and checked the other spades on it to see if any of them were hot at the same time.
I highly recommend a volt meter, 12 and 6 volt test light of some sort with alligator clips or ice pick point on it and a way of testing continuity.
I am not sure of the other parts where you need a resistor and diode. So far I have not experienced any smoking switches or wires and my tractor has not caught on fire. I guess I am just running on dumb luck. THe Amp MEter shows charging properly unless I have all 5 lights ( one in rear ) and am under 600 - 800 rpms and then i show discharging.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Ford N-Series Transmission/Hydraulic Fluid - The Full Story - by Llamas. The transmission fluid in an “N”:-series tractor lubricates the transmission, differential, rear wheel bearings, PTO and hydraulic pump drive, and it also cats as the working fluid for the hydraulic lift. In 9N/2N models, it also lubricates the steering sector and shaft system. The owner’s manual for the 9N and 2N models specified the use of only two fluids. They were STRAIGHT MINERAL OIL SAE 90 (above freezing) and
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
