Posted by TX656 on February 23, 2009 at 22:20:57 from (71.48.165.87):
Tractor Vet stated "do not think that you are going to like what i have to say here"
...Nah, that's OK, I kind of figured she'd be close to needing her overhaul based on what I've read on the board (gas = 5,000 hours, diesel = 10,000?) Doubt I've put more than two hundred gallons of gas through her since I bought her two years ago. I've run 93 octane (but not the low ash oil). No idea on what the prior diet consisted of. I did put a gas filter on it but I think I can remove it now. Magnets in the tank and sediment bowl seem to have gotten the crud out. Came with a very nice loader with very little use. I got a great deal on the tractor because no one could get the loader to work consistently (turned out to be a coupler!) I'm in it right so spending some cash is ok.
I have begun the tear down. So far I'm impressed with how easy the components are to access and to remove. Much easier and less time involved than some car engines I've pulled in the past.
While pulling off the intake found this hole in the feed to the carburetor. Makes the air cleaner kind of irrelevant.
Top end seems clean enough. I was expecting a little more varnish/sludge. Guess it doesn't get very hot up here.
Victor head gasket indicating someone's been in here prior?
Generally the condition of each combustion chamber resembles this one
No scoring in the cylinders. #5 and #6 have a cylinder ridge; my guess would be thickness of the ridge is about the thickness of sheet of 20# copy paper. (I can just hook a finger nail on it.) Ridge in #1 and #2 is almost nil.
Is this an original piston? Or, at 4360 hours will this be the 2nd rebuild?
Bottom end also seems clean enough.
Rod bearings shot. Presuming cam and mains are in similar condition
Except for any work the head will require I'd like to do everything myself. With the money saved by not regrinding the crank or having it line bored seems like I'd have enough to replace the clutch. Not trying to be penny wise and pound foolish but I do need to be effective.
Now that we've confirmed the condition of some of the components what are Tractor Vet's and everyone else's thoughts for rebuild options. At a minimum??? At a maximum???
Can I plastiguage the crank and put in oversize bearings if necessary with out a regrind?
"If you decide to rebuild then there are things that you or your machine shop need to know and i can help on this...." I'm listening
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Tractor Profile: Allis-Chalmers Model G - by Staff. The first Allis-Chalmers Model G was produced in 1948 in Gasden, Alabama, and was designed for vegetable gardeners, small farms and landscape businesses. It is a small compact tractor that came with a complete line of implements especially tailored for its unique design. It featured a rear-mounted Continental N62 four-cylinder engine with a 2-3/8 x 3-1/2 inch bore and stroke. The rear-mounted engine provided traction for the rear wheels while at the same time gave the tractor operator a gre
... [Read Article]
Latest Ad:
Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
