Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Super C sleeves in Super A block


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Janicholson on January 21, 2009 at 21:12:53 from (68.112.156.69):

In Reply to: Super C sleeves in Super A block posted by Wild Bill Caldwell on January 21, 2009 at 20:36:02:

If it is a press fit, it might be hard to get out. If it is pressed in, it will probably not leak from a tiny rusting in of the sleeve in the bore. If rotatable, it relies on the "O"ring to do the sealing, and is designed that way. If you didn't deepen the ring groove, it will for sure fill the groove with squished "O"ring, and not leak. But it will be necessary to use good practices on insertion, including polished edges on the hole, and sleeve entry bevel to avoid scraping or knicking the ring. as well as using straight dish detergent on the rings and sleeve to allow slipping into the hole W/O excess force. It may take some force as the "O"ring will be compressed a bunch.
On the above block height of the ring, I would go for the .004" mark. This prevents excess pinching at the combustion chamber, which can make the gasket edges around the waterjacket and external block seal less tight than good practice. If you are putting in high dome (high altitude) pistons, and the big bore, calculate the compression ratio.
Use the new engine displacement divided by 4. converted to CCs (Swept volume). CC the combustion chambers (select the smallest of that lot) then subtract the volume of the dome on the piston sticking up into it, and add the compressed thickness of the gasket (as a volume of the hole where the combustion chamber is located) to ad to the combustion chamber CC (old gasket for thickness)
Take the total swept volume of one cyl and divide the total combustion chamber real volume into it. For example if swept volume of one cyl was 480cc, and volume in combustion chamber plus head gasket, minus dome volume was 64cc, the compression ratio would be 7.5:1 Shaving .125 might be excessive. There is water in the head that might find new holes to get into oil (I do not know how far one can go, but others may). A cylinder pressure of more than 165 PSI is obtainable. As is the nead for premium. Fast engines can use more compression and more davance. but these slow crankers will die from detonation, they just can't handle the flame front travel rate of regular and high compression. keep us in the loop. JimN


Replies:




Add a Reply

:
:
:

:

:

:

:

:

:

Advanced Posting Options

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.



 
Advanced Posting Tools
  Upload Photo  Select Gallery Photo  Attach Serial # List 
Return to Post 

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Tractor Profile: Allis-Chalmers Model G - by Staff. The first Allis-Chalmers Model G was produced in 1948 in Gasden, Alabama, and was designed for vegetable gardeners, small farms and landscape businesses. It is a small compact tractor that came with a complete line of implements especially tailored for its unique design. It featured a rear-mounted Continental N62 four-cylinder engine with a 2-3/8 x 3-1/2 inch bore and stroke. The rear-mounted engine provided traction for the rear wheels while at the same time gave the tractor operator a gre ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy