Posted by ScottyHOMEy on June 01, 2008 at 18:27:02 from (70.105.241.102):
My answer might be in the books but I haven't plowed through them yet. Was wonderin' if somebody has a quick answer to a long-winded question about splittin' an A.
Neighbor Dave got so much into my BN project (he lent me his heated and well-lighted garage last to get her painted and put back together -- SUPER nice guy!) that he now has an A of his own. Clean, but the motor's stuck, so we're gonna have to split her.
He's already fabbed up a channel iron frame to take the place of the motor so we can roll the chassis back outside while doin' the motor job, which I thought was a pretty clever idea.
My concern on the split has to do with the steering shaft and what, if anything, to do with it for the short time she'll be split. My BN has the u-joint in the shaft. I got the pin out but couldn't get the joint off either end of the shaft, so wound up unbolting the steering support from the top of the tranny when I split it, so I was able to lay the steering wheel and support down on the floor
But the A has the straight (no joint) steering shaft, so I'm not sure the approach I used on my BN will work in this case, even for the short time we'll have her apart to pull the motor and replace it with the channel iron.
Our basic plan is to chock out the steering on the front and support that end on a chainfall, and get the 6"-8" clearance to back the shaft out and clear the flywheel and clutch by rolling the back end away to lift the motor.
Are the guts of the steering mech at the front enough to hold steering wheel and shaft up while we've got her apart? If needs be, I can see pulling the bolt to separate the top end at the bearing/bushing that the shaft passes through, just so the weight of the support can be eliminated, but that still seems like a lot of leverage with the weight of the shaft and wheel just hangin' off of the front end.
The question, I guess, is how have you done it? Any tips other than havin' one of Dave's kids hold the wheel up while we do our wrenchin' thing??
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Tractor Profile: Allis-Chalmers Model G - by Staff. The first Allis-Chalmers Model G was produced in 1948 in Gasden, Alabama, and was designed for vegetable gardeners, small farms and landscape businesses. It is a small compact tractor that came with a complete line of implements especially tailored for its unique design. It featured a rear-mounted Continental N62 four-cylinder engine with a 2-3/8 x 3-1/2 inch bore and stroke. The rear-mounted engine provided traction for the rear wheels while at the same time gave the tractor operator a gre
... [Read Article]
Latest Ad:
Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
