Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

M tranny update


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Randy-IA on April 25, 2008 at 20:06:55 from (207.177.83.243):

Hi All , Had most of yesterday and all of today called due to rain so I got to work on the M . It took most of the time I had yesterday to take the differential apart and clean it ( forgot all about it before ) and get it installed . Today , after 3 hours of trying to set the side to side movement to as close to nothing as possible and get the backlash set at the same time we finally got zero side play with no apparent side loading and .012 backlash . That's as close as we could get on the backlash for some reason . If I took a thin shim out it would drop to .004 or less . The thin shim mic'ed at .006 . I tried to clean the shims up some more when it was at .012 but that didn't help so that's where it is now . Had the pto housing in for a few days with high tack all over it . DUH , can't get the bull gears in with the pto shaft in place . Had trouble getting the the first axle carrier together , learned some lessons and the other one took about an hour from start to finish . So , all the guts are back inside , everything turns smoothly , axles are in , all is good . Tomorrow will consist of getting a broken bolt out of the cover for the steering mount , putting the shift rails back on it and putting it back on , putting in the clutch along with whatever body parts I have time to get on and last but not least , the wheels . Unless there's something I forgot to buy to get it put together . This has been one expensive pilot bearing failure but now every bearing , bushing and seal to the rear of the clutch is new except for the brake band bushings . ...Randy


Replies:




Add a Reply

:
:
:

:

:

:

:

:

:

Advanced Posting Options

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.



 
Advanced Posting Tools
  Upload Photo  Select Gallery Photo  Attach Serial # List 
Return to Post 

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Niagra View Mobile - Powered by a 1959 Ford Tractor - by Mark Massey. In 1959 the Niagara Frontier Transit Inc. of Buffalo, New York designed and built six Viewmobiles for the Niagara Frontier Sightseeing Inc. for use as a sightseeing ride at the Niagara Falls State Park, Niagara Falls, New York, powered by a 1959 Ford 611 Tractor. ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy