Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Farmall 400 not charging


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Bob M on February 06, 2008 at 08:22:44 from (151.190.254.108):

In Reply to: Farmall 400 not charging posted by Duanes on February 06, 2008 at 06:42:20:

third party image

Duanes - If your 400 has have a Delco internally-regulated alternator procede as below. (Otherwise just disregard....!)

1 - Take voltage readings at the following points (all voltages measured to ground):

----

The large post ("BAT") terminal - should read battery voltage.

Now pull the auxiliary wiring connector from the alternator and take readings at the connector.
With the ign switch "off" you should see 0 volts at #1 and battery voltage at #2.

With the ignition switch "on" you should see battery voltage at BOTH terminals.

If you don't get the above results the alt is wired wrong, or there's an open diode (or blown indicator lamp if equipped) in the #1 circuit.

----

2 - If wiring checks out OK, next test the alternator:

Start and run the engine at about 1/2 throttle. Now with an assistant observing the ammeter, find the "D" shaped hole in the back of the alt (photo above...), take a small screwdriver poke it into the hole until it touches the metal test tab inside then ground the side of the screwdriver against the metal case. If the ammeter indicates full charge with the test tab grounded, the internal regulator is bad and needs to be replaced. However if there's still no charge the alternator is N.G. - time for a replacement!

Hope this helps...


Replies:




Add a Reply

:
:
:

:

:

:

:

:

:

Advanced Posting Options

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.



 
Advanced Posting Tools
  Upload Photo  Select Gallery Photo  Attach Serial # List 
Return to Post 

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Ford N-Series Transmission/Hydraulic Fluid - The Full Story - by Llamas. The transmission fluid in an “N”:-series tractor lubricates the transmission, differential, rear wheel bearings, PTO and hydraulic pump drive, and it also cats as the working fluid for the hydraulic lift. In 9N/2N models, it also lubricates the steering sector and shaft system. The owner’s manual for the 9N and 2N models specified the use of only two fluids. They were STRAIGHT MINERAL OIL SAE 90 (above freezing) and ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy