Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: OT-- Crane Accidents


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by T_Bone on October 24, 2007 at 11:02:36 from (4.240.42.150):

In Reply to: OT-- Crane Accidents posted by El Toro on October 24, 2007 at 09:20:44:

Hi Hal,

I too have seen this photo several years back and it just has to many things wrong in the photo.

I've rigged many cranes, both hydro and stick cranes, and I have yet seen where the operator would try and pick 1/10 the load rating from the side of the crane. It just isn't done as it can't be done.

Then there's the headache ball (the lack of) right up against the end of the boom as the load is clearing the water. From here the only thing the operator could do is boom up thus would have to lower the headache ball while booming up. As rigged this creates even a heavier bind on the sea wall.

The headache ball is missing. This is a counter weight for the lifting cable. Without the headache ball the cable will not feed out from the spool and the cable would then rat nest on the spool, just like line on a fishing reel does.

The load center of gravity is all wrong for where the rigging is attached. The load would be more vertical had it been picked this way.

The crane is too small for the water weight it has to pick and mush less not considering the weight of #1 crane.

I've was the master rigger on a 250ton stick crane where the jib boom broke. It was the crane owners fault for exceeding the load rating of the jib boom (a smaller lighter weight rated boom). That was a 11,000lb load on a 250ton rated crane. Were very lucky that no one got hurt.

So I call BS on the photo.

T_Bone


Replies:




Add a Reply

:
:
:

:

:

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Box Plow Blues - by Tom Schwarz. One of the first implements most tractor owners obtain is the box plow. For very little money, this piece of equipment promises to plow and flatten any hill or vale on your ranch road or farm. At least that's what I thought! As simple as a box plow appears, it can be rather challenging to make work correctly. In our sandy soils of Florida, traction is king. You can never have wide enough tires or heavy enough weights to get all the traction you want … unless you own a monster tractor. U ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy