Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Need help w/ bearing seal


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by ScottyHOMEy on August 06, 2007 at 20:30:34 from (64.222.248.53):

In Reply to: Re: Need help w/ bearing seal posted by Bob Kerr on August 06, 2007 at 20:00:28:

I was hopin' you'd chime in, Bob, with all the work you did quietin' down your H.

This is the bearing on the side of the transmission case where the shaft comes out to carry the power to the final drive. It is similar to the way the bull pinion comes out to the brakes on my SuperC (which I might suppose is similar to the setup on the H).

If I had to compare it to another part, it looks like a bigger version of the bearing retainer on the tranny input shafts, after you get the yoke off, only larger. The bearing behind it is 2-1/2" or so in diameter (outside).

Basically, it's machined round and has maybe a little flange on the outside and three ears for bolting it up to the tranny. In the particular spot on the BN, it's under that flange and ears that you shim the shaft. I didn't measure it when I had it open, but as best I recall from the one on the other side that went easily, it's an inch and change deep at most. I can get a chisel under each of the ears to get it started out, but the fit is too tight to turn by hand so, as I said, I've tried walking it out by tapping wedges in turn going around it. It'll come just so far, maybe halfway and bind. I've tried keeping it squared up and tapping the ears to turn it, trying to find a better spot for it to continue coming out. No dice.

I'm about at my wit's end with it. It's one of those parts that'd be the very devil to replace, so I don't really dare to warm onto it with the hammers. In keeping with the hammer rule, I know I could get it out, but the point of the exercise os to have something to put back in. ;8^) But it's the only way into that bearing.

Thanks, and I'll keep ya posted.


Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Tractor Profile: Allis-Chalmers Model G - by Staff. The first Allis-Chalmers Model G was produced in 1948 in Gasden, Alabama, and was designed for vegetable gardeners, small farms and landscape businesses. It is a small compact tractor that came with a complete line of implements especially tailored for its unique design. It featured a rear-mounted Continental N62 four-cylinder engine with a 2-3/8 x 3-1/2 inch bore and stroke. The rear-mounted engine provided traction for the rear wheels while at the same time gave the tractor operator a gre ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy