Farmall & IHC Tractors Discussion Board |
2-71 Super M
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by markloff on August 04, 2007 at 00:01:54 from (70.41.89.9):
FINALLY!!! All the mechanical work is done. (well enough for now) This was my winter project. It's a '53 Super M with a 2-71 GM two stroke Diesel. It turned out to be a lot more work than I thought but I did a lot of different stuff to it also. I completely rebuilt and re-machined the brakes (I can drag a tire with my big toe), new seals all around, completely rebuilt the front end, all new steering, rebuilt shifter, tranny seems good and quiet because it was a loader tractor for many years, dual air filter set-up with K&N filters inside, electric radiator fan, new radiator. The engine runs out at 2100 RPM max and should put out about 65 HP. I'll find out next weekend at a local tractor show. I machined up a custom billet rear cover for the engine and I machined about a 2 inch spacer between the crank and flywheel. This allows you to use the stock flywheel, clutch and starter location. Everything is balanced up also. 2-71's have counter balance shafts and the engine runs amazingly smooth for a two cylinder. I also made a custom oil filler, air intake and relocated the original oil filter and breather so I didn't have to cut the hood at all. Believe it or not it is not very loud either with a muffler and a good silenced air intake. I had a straight intake on it this spring and those 2-stroke blowers make as much noise as the exhaust! I've got K&N filters inside the original oil bath air cleaners and a lot of rubber inside them also so it silences it nearly completely. Next I want to get some nice 16.9's on it since the rims are already widened 2 inches and eventually paint. For now though I'll just have to be happy playing with it at the shows the next few months and a tractor ride this weekend to re-familiarize myself with my family. I’ve been known as that “guy in the shop” for a too many months now! I can answer any other questions. Fire away. Mark
Replies:
Home
| Forums
Today's Featured Article -
Tractor Profile: Allis-Chalmers Model G - by Staff. The first Allis-Chalmers Model G was produced in 1948 in Gasden, Alabama, and was designed for vegetable gardeners, small farms and landscape businesses. It is a small compact tractor that came with a complete line of implements especially tailored for its unique design. It featured a rear-mounted Continental N62 four-cylinder engine with a 2-3/8 x 3-1/2 inch bore and stroke. The rear-mounted engine provided traction for the rear wheels while at the same time gave the tractor operator a gre
... [Read Article]
Latest Ad:
Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|