Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: 12v conversion for super a


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by John T on February 16, 2007 at 16:15:28 from (66.244.90.5):

In Reply to: 12v conversion for super a posted by GWINN on February 16, 2007 at 16:00:56:

If you really wanna use a true One Wire Alternator, thats a piece of cake to wire, but as compared to a cheaper GM 10 SI 3 Wire, they can take higher RPM to kick in and a few of them (depend on internal regulator circuitry) can cause a very minor trickle discharge when setting.

The big main output of a true One Wire Alternator wires to the Load (NOT battery/starter) side of the ammeter, thats the same place where the Gennys Voltage Regulator BAT terminal used to connect. Depends on the alternators amp rating, but Id use at least 10 gauge wire from the alternator to the ammeter and also from the ammeters other Supply side terminal to the battery/starter connection.

NOTE 1: If your just now switching from Pos to Negative ground (as most all alternators use) the ammeter leads would now be reversed or it would read bass ackwards. The Supply side wires to the battery/starter and has ONLY one wire while the load side wires to the alternators output PLUS feeds hot battery voltage to the lights n ignition (via their switches BAT input terminals)

NOTE 2: If its a coil ignition and you change to Negative Ground, the coil should wire + from the ignition switch and - to the distributor.

NOTE 3: If it had a 6 volt coil you can EITHER add a series external voltage dropping (12 to 6) Ballast Resistor in the line from the ignition switch to the coil ORRRRRRRRR use a full true 12 volt rated coil and no ballast is required.

Of course, change any lights to 12 volts

If I missed anything I hope the other gents will add to this, let me know if you have any questions:

John T


Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Ford N-Series Transmission/Hydraulic Fluid - The Full Story - by Llamas. The transmission fluid in an “N”:-series tractor lubricates the transmission, differential, rear wheel bearings, PTO and hydraulic pump drive, and it also cats as the working fluid for the hydraulic lift. In 9N/2N models, it also lubricates the steering sector and shaft system. The owner’s manual for the 9N and 2N models specified the use of only two fluids. They were STRAIGHT MINERAL OIL SAE 90 (above freezing) and ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy