Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: PTO won't work on IH 1066


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by the tractor vet on June 08, 2006 at 20:23:03 from (64.179.117.134):

In Reply to: PTO won't work on IH 1066 posted by NHBalerman on June 08, 2006 at 20:02:18:

More then likely you sheared the tiny littel pin that hold the valve together . To fix you have to take off the square not on top that the linkages hooks to then drop the plug on the bottom and remove the valve from the bottom and if ya have a two pice valve then the pin is sheared and can be bought at the local Case I H dealer . Now the down side is that the square nut that you took off the top that is how you set the clutch lock up pressure and ya need the special fitting to go into the test port and a gauge that will read 600 lbs. , Now you can buy the fitting for Case I H if the dealer will let you as it is a special test TOOL and sometimes they get funny about ordering it . The gauge you get them from any place that sell a good Hyd. Gauge Now if you can get the fitting you turn the valve stem into the nut with a small nail thru the small hole in the stem till you get around 245-265 lbs. of pressure on the gauge with the hyd . Oil at about 150-180 degrees or operating temp. When i do the set up i have a leg up on ya as i run the tractor hooked to my Flow Rater and warm the Hyd. oil with it and it has a temp gauge on it . Or you can just have the dealer fix it . Also if you have the wick turned up on that 1066 myself i would even run the lock up pressure up to 265-285 that way you will never walk it thru the clutches if you are doing any heavy PTO work. If it is somewhere near stock + 10-15 % then the first pressure set will be fine.


Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Tractor Profile: Allis-Chalmers Model G - by Staff. The first Allis-Chalmers Model G was produced in 1948 in Gasden, Alabama, and was designed for vegetable gardeners, small farms and landscape businesses. It is a small compact tractor that came with a complete line of implements especially tailored for its unique design. It featured a rear-mounted Continental N62 four-cylinder engine with a 2-3/8 x 3-1/2 inch bore and stroke. The rear-mounted engine provided traction for the rear wheels while at the same time gave the tractor operator a gre ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy