Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Farmall H 12 Volt Conversion.


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by John T on March 16, 2006 at 10:56:01 from (66.244.90.98):

In Reply to: Farmall H 12 Volt Conversion. posted by Bunchs33 on March 16, 2006 at 08:54:01:

Bunchs, Just sitting here and from what you say I cant be sure if you really mean an "electric solenoid" or a mechanical start switch (which normally has only 1 big external post where a battery cable attaches (the other underneath the switch and possibly a small one out the side) but will proceed based on you actually having and asking about an electric solenoid.

Its best at 12 volts to use a solenoid with a 12 volt rated coil. Otherwise, she may overcurrent and overheat, but could work a long time fine depending on how long its activated and its design.

Now, you ask about 3 or 4 terminals. On many older solenoids, ESPECIALLY the 6 volt units, they had the big in (from battery) and out (to starter) terminals plus a single small terminal possibly labeled S or possibly no label. Thats the activation terminal which leads to a push to start or a start switch which is HOT to operate the solenoid when in the START position.

On many 4 terminal solenoids ESPECIALLY the older Ford types mounted up near the battery, they had the 2 big in n out posts plus 2 small terminals labeled S and I. If you have one of those, the S is the activation terminal which wires to the start switch to operate the solenoid while, the I Ignition terminal is hot ONOLY when cranking and can be used to by pass an ignition ballast if the auto or truck or tractor had one. If you have no ballast then you just use the S terminal.

An electric solenoid has to have a starter with a drive gear (Bendix) that engages into the flywheel (mechanically or electrically) when she cranks, while many mechanical activated starter drive gear mechanisms use the lever action to push the drive gear into place and then the electrical switch closes to spin the starter motor and engine. Im just not sure what you have there so I cant fully give you an answer, sorry.

John T




Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Niagra View Mobile - Powered by a 1959 Ford Tractor - by Mark Massey. In 1959 the Niagara Frontier Transit Inc. of Buffalo, New York designed and built six Viewmobiles for the Niagara Frontier Sightseeing Inc. for use as a sightseeing ride at the Niagara Falls State Park, Niagara Falls, New York, powered by a 1959 Ford 611 Tractor. ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy