Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: IH #8 Plow Shares


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Hugh MacKay on February 19, 2006 at 15:44:43 from (64.228.11.28):

In Reply to: Re: IH #8 Plow Shares posted by Dave NE IA on February 19, 2006 at 14:06:46:

Dave: Are you looking for the address of the guy I deal with or his source of parts in Iowa.

Now I should qualify what I said about TSC Stores being the best source of wear parts for older plows here in SW ON. I think the "best source" part of it should go to an individual that works there rather than the store chain TSC. Most of their staff look at you as though you had two heads when you ask for parts for a No. 8 plow.

Joe is an ex IH partsman, he is also quite keen on old plow days as well as match competition plowing. He may well give me the address of that source in Iowa. I don't think it will do you much good contacting anyone here in Canada. The Canadian built IH plows were built at Hamilton Ontario were different from US built plows having the same model number. Just to give you an example, you folks call the No. 8 plow a No.8 Little Genius, here in Canada it was called a No.8 Tractor plow, no mention of the words Little Genius. The plow frames were different. I suspect the bottoms were the same. However I've never been able to confirm that.

All US built IH plows prior to 1958 had diagnol cross members, right? All Canadian built IH plows used pertendicular cross members. The Canadian plows also used ACE bottoms quite often, but also used a general purpose bottom very similar to yours, but as I said I'm not certain they were the same part number.

For that reason I suspect the Iowa source of parts would best serve your needs. I may take me a few days to find the address. I will send you an e mail.


Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Ford N-Series Transmission/Hydraulic Fluid - The Full Story - by Llamas. The transmission fluid in an “N”:-series tractor lubricates the transmission, differential, rear wheel bearings, PTO and hydraulic pump drive, and it also cats as the working fluid for the hydraulic lift. In 9N/2N models, it also lubricates the steering sector and shaft system. The owner’s manual for the 9N and 2N models specified the use of only two fluids. They were STRAIGHT MINERAL OIL SAE 90 (above freezing) and ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy