Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Farmall H Starting Problems.....


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by john d on December 27, 2005 at 20:00:39 from (69.128.202.89):

In Reply to: Farmall H Starting Problems..... posted by Farmall H PA on December 27, 2005 at 14:02:03:

If it has gas, spark, compression, and is timed correctly, it will run.

You've got gas dripping from the carb, so you know it has fuel that far, at least. I'd look for spark next. Remove a spark plug wire from the mag cap. Let it hang in mid-air while still attached to the mag. Get a long screwdriver with a wood or plastic handle. Put the tip of the blade firmly against the engine block, and have someone crank the engine over WITH THE IGNITION SWITCH ON while you move the blade of the screwdriver close to the end of the plug wire. If you have spark, it will jump from the wire to the screwdriver. You won't get shocked, as it will go back to the engine block. If you can't get a spark that way, then it's time to dig into the mag. If you do get a healthy-looking blue spark (reddish may indicate poor condenser) then pull the spark plugs. If they are wet with gas, clean them. Don't just clean the threaded end, wipe the porcelin insulator with a paper towel to remove moisture, dirt, etc. While they are out, crank the engine a couple of turns to put some clean air inside
before re-installing the plugs.
If the gas is old, all bets are off.

As a previous poster indicated, they each have their quirks about how much choke they want. I'd start with about 1/4 throttle and no choke. Get the engine spinning, then add a LITTLE choke if needed.

If the thing remains completely reluctant, or if the battery is about gone, consider applying 12 volts directly to the starter. Don't touch the starter switch on the tractor when doing this, and the 6volt system will remain isolated from the 12 volts. If you go the 12 volt routine with jumper cables, wear some safety goggles, and don't have stray sparks anywhere NEAR any dripping gasoline or gas fumes!


Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Ford N-Series Transmission/Hydraulic Fluid - The Full Story - by Llamas. The transmission fluid in an “N”:-series tractor lubricates the transmission, differential, rear wheel bearings, PTO and hydraulic pump drive, and it also cats as the working fluid for the hydraulic lift. In 9N/2N models, it also lubricates the steering sector and shaft system. The owner’s manual for the 9N and 2N models specified the use of only two fluids. They were STRAIGHT MINERAL OIL SAE 90 (above freezing) and ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy