Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: snowplow for 230


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Hugh MacKay on December 17, 2005 at 03:32:23 from (216.208.58.188):

In Reply to: snowplow for 230 posted by jason S on December 15, 2005 at 12:06:19:

jason: The blade Dave speaks of will be hard to find, mainly as not a lot of new tractors were sold with snow blades. I suggest you save the effort and either fabricate or buy something suitable.

Does your 230 have one hydraulic valve or two. It can be equiped with two valves and they are rather easy to find. That same valve was used on numerous IH tractors, all the way from 300 to 560. The big tractors all used that valve. I have seen a 230 with two hydraulic valves with a plow off a pickup mounted out front. One valve was used to lift and the other to power angle the blade. You just need a drop frame below front axle, make sure it is supported or braced to rear axle cariers, this reduces shock load on tractor castings.

You can also do a complete fabrication along the same lines as pickup blade. The 72 blade Dave speaks of and the 60 used on SA, 130, etc were same basic design. The model numbers really just designate the blade width in inches. That design also is not a lot different from pickup blades.

If you notice today, there are a lot of blades on big tractors, and I mean 100 hp plus 4x4, same idea as the pickup blade. There are a few of them around here doing shopping mall parking lots, some of them with 16' to 20' wide blades. I expect you can buy one just right size for 230. These blades are being made for lawn and garden tractors, thus I would think everything in between. They are an aftermarket blade, porobably more than one of them, but all are adaptable to most tractors.

If you wish to see blades go to tractor photos, type in C, SC, 200, 230, etc. you will find some with blades Even take a look at the offsets, may give you some ideas. Look in photo adds there is a pickup blade in MI for $100.


Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Niagra View Mobile - Powered by a 1959 Ford Tractor - by Mark Massey. In 1959 the Niagara Frontier Transit Inc. of Buffalo, New York designed and built six Viewmobiles for the Niagara Frontier Sightseeing Inc. for use as a sightseeing ride at the Niagara Falls State Park, Niagara Falls, New York, powered by a 1959 Ford 611 Tractor. ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy