Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: International A110 Pickup truck


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by T_Bone on November 27, 2005 at 17:49:16 from (4.240.90.240):

In Reply to: International A110 Pickup truck posted by Nebraska Cowman on November 27, 2005 at 06:45:31:

Hi NC,

I can't help with the A110 but depending on which PSD you want to use. Mine is a 02 F350 PSD with a ZF6spd, 3.73, DRW, 4wd, and with 26kGCW at 1800rpm I had no problem maintaining 60mph on flat roads in 6th(OD) and 5th gear on the small hills.

The 02 PSD makes 520ft/lbs at 1600rpm and 275hp@2800rpm. Other years, 99'+, are slightly less with the 03 7.3 slightly more.

I added a 2nd tractor for 31kGCW and that was too much for this truck. I now had to use 2250rpm to 2500rpm (turbo rpm) to maintain 60mph. I was also fighting a 30mph headwind.

I normally pull my RV, 16kGCW, at 1600rpm on the flats and 1800rpm on the 8% grades. At 1800rpm the turbo adds just a tad of boost and makes a huge difference in climbing the grades.

I drive for maximum fuel ecomony at all times so most of my travels is at 1600rpm as this yeields the best fuel mileage.

The Ford ZF6spd is a piece of junk and shifts like one. Also the stock Ford or LUK clucth is too weak for the PSD. Both Rockwell and Southbend build a clutch rated at 11ooft/lbs or enough to last in a PSD.

Personally I would look at a older mechanical injected diesel with a turbo as then you can run B100 or home made fuel where the PSD will have a few problems with back yard fuel.

I would also look at a Eaton 18spd auto-shift tranny as then you can have a double OD for great fuel ecomony plus have a 17% ratio spread. The autoshift needs a clutch to stop and start but up/down shifts like a fluid automatic but with gears and no clutch to shift. It shifts by rpm that you program in and can change at will.

I have a neighbor that uses a 6cyl Ford tractor engine in his pick-up. He stated the engine has worn out two pick-ups and now working on it's 3rd truck. He keeps the engine & tranny and fuel componets and changes the rest of the truck.

T_Bone


Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Niagra View Mobile - Powered by a 1959 Ford Tractor - by Mark Massey. In 1959 the Niagara Frontier Transit Inc. of Buffalo, New York designed and built six Viewmobiles for the Niagara Frontier Sightseeing Inc. for use as a sightseeing ride at the Niagara Falls State Park, Niagara Falls, New York, powered by a 1959 Ford 611 Tractor. ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy