Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Farmall Super M Head Installation .


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Keith-OR on November 23, 2005 at 18:09:09 from (207.200.116.203):

In Reply to: Farmall Super M Head Installation . posted by LumbrJakMan on November 23, 2005 at 15:17:02:

This comes directly out of 1974 Motors repair manual. I have used this method for many years after a couple of engines I rebuilt had a water seepage on the head gasket. Had no problems with that problem since...

Cylinder Head Replace

Notes

Before installing cylinder head, wipe off engine block gasket surface
And be certain no foreign material has fallen into cylinder bores, bolt
holes or in the valve lifter area. It is good practice to clean out bolt
with compressed air.
Some cylinder head gaskets are coated the special lacquer to provide
a good seal once the parts have warmed up. Do not use any additional
sealer on such gaskets. If the gasket does not have this lacquer coating
apply suitable sealer to both sides

Tighten cylinder head bolts at a little at a time in three step in the
sequence shown in the illustration. Final tightening should be to the
torque specification listed in the engine tightening table. After the
bolts have been torqued to specifications, they should not be disturbed.

In instances where cylinder head gasket leakage is hard to control,
aluminum paint can be applied to the gasket as a sealer.

Spray one coat of the aluminum paint on both sides of the gasket
and allow the paint to dry. Then spray a second coat on both sides
and while the paint is still wet, install the gasket. Torque the head
and manifold bolts to specifications to complete job.


Keith


Follow Ups:




Post a Followup

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Box Plow Blues - by Tom Schwarz. One of the first implements most tractor owners obtain is the box plow. For very little money, this piece of equipment promises to plow and flatten any hill or vale on your ranch road or farm. At least that's what I thought! As simple as a box plow appears, it can be rather challenging to make work correctly. In our sandy soils of Florida, traction is king. You can never have wide enough tires or heavy enough weights to get all the traction you want … unless you own a monster tractor. U ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy