Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Voltage regulator question.............


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Bob M on September 22, 2005 at 06:11:02 from (151.190.254.107):

In Reply to: Voltage regulator question............. posted by Capt. Minx on September 21, 2005 at 19:55:32:

Cap'n - If there is nothing identifying the regulator voltage (look carefully for a voltage/polarity stamped on the underside of the base) you can still determine whether it’s 6 or 12 volts using a 12 volt battery:

Remove the regulator cover and identify the cutout relay. It will be the relay with 2 windings - a few turns of heavy wire wound onto another of many turns of fine wire. Also it will be the only relay with it’s contact points held OPEN by spring pressure. (The voltage and current regulator relay contacts are held closed by spring pressure).

Ground the regulator base to one post of the 12 volt battery (doesn’t matter which one…). Now while watching the cutout relay armature, use a jumper wire to momentarily connect other battery post to the regulator’s GEN terminal. If the cutout relay operates (closes it’s contacts) you have a 6 volt regulator. But if nothing happens the regulator is 12 volt.

---

HOWEVER as a practical matter I discourage installation of a regulator unknown heritage! Regulators are rated not only for voltage but are matched for also for the current characteristics of a particular generator. If you install a regulator mismatched for current rating you risk burning out your generator.

Further I consider regulators “wear items” much like like fan belts, brake linings, etc. Their performance and reliability deteriorates with use and age.

Also....should you happen install a 6 volt regulator onto a 12 volt system, you're at risk for a dead battery, burned out generator or even an electrical fire. Don't do it!

Bottom line: Spend $35 - $40 and get the correct regulator for your tractor than mess with a used one of unknown heritage!




Follow Ups:




Post a Followup

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Niagra View Mobile - Powered by a 1959 Ford Tractor - by Mark Massey. In 1959 the Niagara Frontier Transit Inc. of Buffalo, New York designed and built six Viewmobiles for the Niagara Frontier Sightseeing Inc. for use as a sightseeing ride at the Niagara Falls State Park, Niagara Falls, New York, powered by a 1959 Ford 611 Tractor. ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy