Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Belt Pulley for 39H


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Slappy on September 20, 2005 at 07:40:53 from (143.88.85.82):

In Reply to: Belt Pulley for 39H posted by Triker on September 20, 2005 at 06:28:45:

Triker,

The leak is due to a faulty seal. These are not hard to replace and your HI dealer can still get them. As to draining the oil, the pulley is splash lubricated by the forward transmission gears - so you change the oil in it every time you change transmission oil. The unit is set up to hold a limited amount of oil.

To change the oil in this reservoir and change the leaky seal, you first remove the pulley from the 'wheel' it attaches to. Loosen the bolts (if I remember right 4 of them) on the face of the drive unit and pull the shims, bevel gear, shaft, bearing, seal retainer and wheel out as a unit. A fair bit of oil and probably some water will come out as well.

I think (its been a while since I worked on mine) a snap ring holds the works together. If you can avoid it, leave the big Woodruff ket in place. These come out hard and you almost have to destroy them to get them out. They are available but hard to find. If you have to change the bearing, I think the key will have to be removed - maybe yours will come out easier than mine did. I think the seal retainer will come off without removing the key.

I'm sorry I don't remember the exact sequence, but the parts manual and common sense will give you all of the details you need. A relatively easy fix.

The control is a rod that attaches to an arm on the pulley drive unit and exits the ignition switch plate at the base of your steering support shaft - pull the rod to start the pulley.


Follow Ups:




Post a Followup

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Ford N-Series Transmission/Hydraulic Fluid - The Full Story - by Llamas. The transmission fluid in an “N”:-series tractor lubricates the transmission, differential, rear wheel bearings, PTO and hydraulic pump drive, and it also cats as the working fluid for the hydraulic lift. In 9N/2N models, it also lubricates the steering sector and shaft system. The owner’s manual for the 9N and 2N models specified the use of only two fluids. They were STRAIGHT MINERAL OIL SAE 90 (above freezing) and ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy