Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: IH B414 Transmission Problems


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Janicholson on June 21, 2005 at 11:54:43 from (199.17.6.175):

In Reply to: IH B414 Transmission Problems posted by Ned C on June 21, 2005 at 06:49:22:

There are two possible issues.
1} the shifter leaver tip that moves the shift rails in the transmission could be worn on the end. (PROBABLE)
2}The actual drive gear on the shaft could be engaged, but not on its shift fork. (LESS likely)

Determine which gear the tractor moves in when in neutral. It might also not shift into this gear when moving the lever.

Using a Manual or parts book, disassemble the shifter pivot down at the trans and pull it out of the housing. Use a good little spot flashlight to light inside the hole and see if you can see a rail/slot out of position for that gear (it will be in a location opposite of the position for that gear in the pattern because the pivot reverses the direction of motion. Use a fair sized screwdriver, with the clutch down, to move this shift rail/slot back into alignment with the remaining rails (this is neutral, test it by starting the tractor and releasing the clutch, (it should now not move and the engine should not be pulled down). The tip of the lever (that you pulled out should be appearing worn on the trans end. This tip usually (but not always) looks like a flattened disk, or 4 dimes stacked on each other. It needs to be welded up and reground to its original size. If you can get tough alloy welded onto the original tip, the part will never fail again.

If problem #2 is the case pulling the trans cover off, and doing major surgery on the gears/rails/forks, and detents may be needed.


Follow Ups:




Post a Followup

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Choosin, Mounting and Using a Bush Hog Type Mower - by Francis Robinson. Looking around at my new neighbors, most of whom are city raised and have recently acquired their first mini-farms of five to fifteen acres and also from reading questions ask at various discussion sites on the web it is frighteningly apparent that a great many guys (and a few gals) are learning by trial and error and mostly error how to use a very dangerous piece of farm equipment. It is also very apparent that these folks are getting a lot of very poor and often very dangerous advice fro ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy