Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall Tractors Discussion Board

Re: Can any of you IH guys help with this?


[ View Follow Ups ] [ Post Followup ] [ Return to Farmall Tractors Discussion Board ]

Posted by Burrhead on December 14, 1999 at 19:22:19 from (12.74.16.36):

In Reply to: Can any of you IH guys help with this? posted by John on December 14, 1999 at 13:50:33:

I had 1 and the man is right about the loose baling part, but most times you can over adjust it to make it tighten up the bales. If you take your time and roll a tight bale you can live with it. When you bale, stop at about 1/3 of the bale and let it spin a minit, roll another 1/3 stop and roll it a minit. Then when it gets up to the marker for done just sit there and take about 3 minits, just letting it roll fast before you twine it. Biggest thing to watch for is the bearings and roller shafts being wore out, and the floor being wore out or rusted out.. If the bearings are showing much wear I would pass on it.
I would want it to be real cheap in order to be worth while. I only need about 200 per year so mine was never that much trouble, and if you don't cover the hay for storage. No matter what baler. You will have alot of spoilage anyway compared to squares. I prefer squares myself, but its hard to find help anymore to put it up.
If you can find an old 845 or so New Holland I think you would be alot more happy, and they are pretty reasonable to buy and they do better than the IH..


Follow Ups:




Post A Followup

:
:

: Re: Re: Can any of you IH guys help with this?

:

:

:

:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Ford N-Series Transmission/Hydraulic Fluid - The Full Story - by Llamas. The transmission fluid in an “N”:-series tractor lubricates the transmission, differential, rear wheel bearings, PTO and hydraulic pump drive, and it also cats as the working fluid for the hydraulic lift. In 9N/2N models, it also lubricates the steering sector and shaft system. The owner’s manual for the 9N and 2N models specified the use of only two fluids. They were STRAIGHT MINERAL OIL SAE 90 (above freezing) and ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy