Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

M rewired, fired up, blew starter on restart


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Kevin Brooks on May 11, 2005 at 09:22:03 from (129.33.49.251):

Folks,
Recently rewired my '51 M for alternator and fired it up yesterday...Vrroomm! As I was basically running without any gas tank ('cept what was left in the carb) I needed to shut down. Several hours later I returned to restart the M with a better fuel supply but all I got what a sold thud (sound maybe like started solenoid?) and then my makeshift idiot light went out and I had no power. My battery checked out at 12.56V afterwards - up substantially from the 11.0V prior to first start. When running the new ammeter seemed to hit ~20amp mark (amp scale large at +/- 60amp). My batter to starter cable appears larger than the usual 12v cable, might still be O.E.M from 6v days. Starter is a remanufactured 6v. Front and rear headlamps wires were disconnected due to condition. Light switch was in low or dim position. (Which way is OFF? Decal in worn away and only partial lettering can be seen.) Is there a dimmer resistor which I can replace made for 12v, if not, where could or should I place one? Are there light switches made for 12v systems and would that be more appropriate? Lastly, is there an in-line, smaller-sized resistor that can replace the newly installed ballast resistor?
All help and comments appreciated. Thank you in advance.


Follow Ups:




Post a Followup

:
:
:

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Talk of the Town: Repairin a Gas Tank - by Staff. This interesting discussion is from the Tool Talk Discussion Forum. Remember that safety is your first priority - make sure you know what you are doing before attempting a potentially dangerous activity! ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy