Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo Sorry! Our Phone System is Down. Please use our Contact Us Form.

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: 140 steering adjustment


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Bryan Meade on February 19, 2005 at 06:40:25 from (216.12.83.200):

In Reply to: Re: 140 steering adjustment posted by Dave140 on February 16, 2005 at 19:56:00:

i have had the same on 3 super A's (same as a 140) and every one i had to drop the front axle, remove the bottom half of the steering box, and on 2 of them i had to put a new roller bearing and c clip in the top and a bushing and seal in the bottom, the other one the c clip had just broke and the fan gear shaft was able to travel up and down instead of left to right. i also know that if left unfixed long enough it will wear the fan gear shaft from round to oval. that shaft was about 80.00 at my ih dealer. i havnt been able to make any of the 3 hold gear oil since, so i just removed the small plug and put in a grease fitting. the new seals will hold that. its not a fun job, but i made 2 stilts that bold on the sides of the torque tube, they are just long enough to hold the front end high enough to remove. believe me, i felt a lot safer working under the front with no axle on it with these 2 pieces of steel holding it up instead of blocks and a jack.

so to sum it up, ill bet bad bearing or c clip, i would not let it go to long like that or it will cost more to fix. if its bad also replace the bottom bushing while your there, its only a few dollars. and be careful while the axle is off, its dangerous.

thanks
bryan



Follow Ups:




Post a Followup

:
:
Hide: Yes No
Hiding your address protects you from spam generators but allows you to receive email response notifications.

Subject: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Talk of the Town: Repairin a Gas Tank - by Staff. This interesting discussion is from the Tool Talk Discussion Forum. Remember that safety is your first priority - make sure you know what you are doing before attempting a potentially dangerous activity! ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy