Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Single-Point Hitch/Turning Plow Questions


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Hugh MacKay on February 02, 2005 at 13:01:00 from (64.228.11.112):

In Reply to: Single-Point Hitch/Turning Plow Questions posted by Bill in NC on February 02, 2005 at 06:31:16:

Bill: Do you by any chance know the model number of your plow? I guess I'm just wanting to satisfy my own curiosity on that one.

My first question what is the wheel tread setting on tractor, center to center on rear wheels. I find my plow gives optimum performance at 52" tread setting. I can make 56" work, but it is a bit of a chalange. I have never tried 48". Is the levelling screw on the left side of hitch? I've seen a few of those get changed to right side of hitch, just will not work. Sounds to me as though your levelling crank, and on the left must be lengtened.

One other item you will find with those little plows, points will wear down to a certain point, and that is it. From there it just seems as though that right front moldboard will ride the left rear moldboard right out of soil. It seem as though the more you lower the depth control the worse this situation becomes. It is rather frustrating as I have seen trailer plows with same moldboard and point, that would plow well with more wear.

One thing I quite often do is weld truck spring on top of point tip. I weld this parallel with line of travel, extend it back and up point 6", thus allowing 4 to 5 inches to protrude past end of point. This tends to replace point, thus giving plow more suck. I find you can only do this once with each set of points as the share portion is worn by then.


Follow Ups:




Post a Followup

:
:
Hide: Yes No
Hiding your address protects you from spam generators but allows you to receive email response notifications.

Subject: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Talk of the Town: Repairin a Gas Tank - by Staff. This interesting discussion is from the Tool Talk Discussion Forum. Remember that safety is your first priority - make sure you know what you are doing before attempting a potentially dangerous activity! ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy