Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: help with 12 volt conversion


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by farmallhal on January 04, 2005 at 18:19:19 from (216.106.33.33):

In Reply to: Re: help with 12 volt conversion posted by jeff smith on January 04, 2005 at 16:25:34:

Jeff, I don't know how to advise you from here if you have it wired per Bob's diagram. As far as testing the ammeter I think you could attach a light (a fan motor or a cigarette lighter would be better) or any 12 volt item which will draw current to one side and a feed from the battery to the other side and see what kind of deflection you get in the pointer when powering up the 12 volt item. You will also have to ground whatever you are trying to power up to the same ground plane to which the battery is grounded or directly to negative post on the battery. You can do this on or off the tractor as long as you can connect the ammeter in the circuit. I would think you should unhook the other leads to the ammeter when doing this test as you just want to see if current is being measured through the ammeter. This electrical trouble shooting is not my speciality in great detail but I do have somewhat of a working knowledge and have been able to survive. I would also put in that 10 ohm - 10 watt resistor I keep talking about as that should be enough draw to excite or start your alternator into a charging mode. I was told the resistor needed to be soldered to the wires for the best connection. Was very easy to do and then go back and install a light along with the resistor once you get this all straightened out if you like the light. Those resistors are really very cheap at Radio Shack. I have only done this conversion once and then with the Hitachi 14231 alternator. I take it you are using one of those older 10SI Delcos and not something which might have an internal diode which would cause problems with what you are trying to do? You should have had a voltage regulator in conjunction with the generator and that should be totaly disconnected out of the conversion as the alternator should have an internal regulator. Send me an email to russell@wavecomputers.net
if you feel you need Bob's email address to get this completed. We all want you to succeed in this endeavor and will help in any way we can. By the way where are you locatedin this great conuntry? Good luck and hang in there and let us know how this progresses, Hal


Follow Ups:




Post a Followup

:
:

Subject:

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Picking Corn - by Rick Nikolich. It was the day before Christmas shutdown at work and I asked our lead engineering expert Scott Andrzejewski what he was going to do over the holidays. He said that he had some corn that he still needed to pick with an antique one-row New Idea corn picker. Scott has a nice farm about an hour north of Lansing in St. Johns, MI. He wanted to get the rest of his corn in by the next day (Christmas Eve). We had about an inch of new snow on the ground and single digit temperatures. So in the bac ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy