Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: I'm Bored Too....


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by ChadS on December 15, 2004 at 05:43:35 from (66.228.96.131):

In Reply to: Re: I'm Bored Too.... posted by Jonboy on December 14, 2004 at 16:54:47:

Jonboy. Thanks for looking! As far as what the H could handle for HP at a constant rate in the fields, well, that I cannot say, on a pulling track, thats a different story though,, I have an H that has a stroker kit in it, and it is a strong 70hp any day of the week. It would run in the fields all day long! Id say inthe fields,, the H could handle a 70 hp powerplant, but not overweighting the frame, to say,, match an 806. you would still only do, what an H can do, not what the 806 can do. but it sure was fun to do that conversion! I made sure the rear end was good, and replaced all the bearings in my 6 cyl conversion H, everything is AOK so far. Bout hthe only thing I can take away from this being a field tractor, is the radiator, and the wide front I had made for it. but, still can bolt onthe origianl 460-560 front end right on. the frame rails were wider across in the 400 series engine and frames. the frame rails still are the same bolt pattern to bolt either one on the bellhousing. just like the small block bellhousing for the 460,, the front bolster from the 560 which was a wider frame rail frame, still had parts available from other models, that could be used to make a swap. IH was like a huge rubix cube on what they did to progress and upgrade. technology,, really did not change that much as far as specifications were concerned in the bellhousing for the starters, clutches, etc. Anyways,, winter is here, got more conversions to figure out. Just a pile of parts, and a wish list. ChadS


Follow Ups:




Post a Followup

:
:

Subject:

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Choosin, Mounting and Using a Bush Hog Type Mower - by Francis Robinson. Looking around at my new neighbors, most of whom are city raised and have recently acquired their first mini-farms of five to fifteen acres and also from reading questions ask at various discussion sites on the web it is frighteningly apparent that a great many guys (and a few gals) are learning by trial and error and mostly error how to use a very dangerous piece of farm equipment. It is also very apparent that these folks are getting a lot of very poor and often very dangerous advice fro ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy