Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: I got my Farmall H fan belt flange to move, Th


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by John in Ct. on September 03, 2004 at 19:54:22 from (192.233.162.169):

In Reply to: Re: I got my Farmall H fan belt flange to move, Th posted by Dave in CT on September 03, 2004 at 09:06:42:

I sprayed the set screw and nut with PB blaster for a few days. I was able to get the nut off but not the set screw out, I was afraid of breaking the set screw. Next I found the same size nut and put 2 nuts on the set screw. I backed the first nut into the second nut with a wrench, had someone also at the same time use a ratchet with a screw driver bit in the slot turning the set screw too and was able to get the screw out. Next I cut the fan belt off and sprayed down the set screw hole and both sides of the pulley flange with PB Blaster. I sprayed it a lot. I also would tap the flange (Unscrew direction) with a brass punch while holding the fan. I did this every day since Sunday and nothing moved at all until yesterday. It moved a little in the morning. I then sprayed it more and came back later and tapped it a little more. Once it moved I knew it would eventially move. Finally last night I was able to brake it free, now you could almost spin it with your fingers. I didn't put the belt on yet. I also at the same time am resealing the engine (The main job). I have the valve cover off, push rod cover off, oil filter housing off, mag off, pan off etc. I am cleanig out sludge. The fan belt is just a fill in job. The key is to spray it, tap a little with a brass punch, stop, let it sit ,then do it a few hours later. I think you asked once where I am in Ct, I am in Colchester.


Follow Ups:




Post a Followup

:
:

Subject:

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Women and Tractors - More Views From the Farmer's Wife - by Teri Burkholder. The top ten reasons why the judges wouldn't let you participate in the stock antique tractor pull: Hey, this is stock! It came with that V8 in it! That "R" on my tires stands for "really old" not radial! Blue gas? We thought it was a pretty color! What wire hooked to my throttle? ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy