Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: 504 distributer fried from wiring mistake?plea


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Bob M on June 25, 2004 at 06:49:51 from (165.170.128.66):

In Reply to: 504 distributer fried from wiring mistake?please H posted by Randy on June 25, 2004 at 05:45:52:

Randy - Except perhaps for a direct hit by lightning it’s pretty hard to ruin a distributor or the plug wires! As long as the points are installed correctly and the contacts are clean, problem’s gotta be somewhere else. You might proceed like this:

1 – Temporarily block the breaker points open - stick a clean business card, dollar bill or similar between the contacts. Now turn on the ignition and check for voltage between each coil primary terminal and ground. You should see battery voltage to ground at BOTH coil terminals.

If voltage appears at the + terminal only, the coil is bad. If you see no voltage at both terminals check for bad wiring harness, burned-out ballast resistor (if there is one), bad ignition switch, etc. If you see voltage at both terminals go to the next step.

2 – Pull the center wire from the distributor cap. Stick a good spark plug on the end of the wire then lay the plug on grounded metal. Now turn on the ignition and manually work the ignition points open and closed. You should get a fat spark at the plug each time you open the points

If you don’t get a spark suspect a bad coil (or possibly a bad condenser). If you get a good spark go to #3.

3 – Problem’s gotta be ignition timing. Check the plug wires are installed in the correct order on the distributor cap. Set the crank to #1 TDC (#1 cylinder firing) then verify the distributor rotor is under the cap’s #1 plug wire nipple.

Hope this helps...




Follow Ups:




Post a Followup

:
:

: Re: Re: 504 distributer fried from wiring mistake?plea

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Choosin, Mounting and Using a Bush Hog Type Mower - by Francis Robinson. Looking around at my new neighbors, most of whom are city raised and have recently acquired their first mini-farms of five to fifteen acres and also from reading questions ask at various discussion sites on the web it is frighteningly apparent that a great many guys (and a few gals) are learning by trial and error and mostly error how to use a very dangerous piece of farm equipment. It is also very apparent that these folks are getting a lot of very poor and often very dangerous advice fro ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy