Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Re: Can I change a rear tire myself?


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Stan(VA). on June 03, 2004 at 05:38:21 from (208.59.157.116):

In Reply to: Re: Can I change a rear tire myself? posted by CNKS on June 02, 2004 at 18:22:13:

I also do mine off the wheel. I lay the rim down behind the Super H or M with 3 pnt hitch and use down pressure to break the bead loose on both sides first. I use a board (2x6, 2x8, 4x4, etc) with the edge cut on an angle to set under one of the lower lift arms and push down on the tire right at the edge of the rim. If you don't have access to a helper tractor like this, you might try letting all the air out of the tire and driving it a short distance to break it loose (assuming the old tire is to be thrown away). I've never had any luck trying to break one loose with hammers. The condition of the rubber on the old/new tires and the condition of the rim can make this a unique experience each time you try it ;)

One thing that has helped me is remember to push one side of the bead into the deepest part (center) of the rim while prying the opposite edge off. This gives you the clearance you need. I just have 1 tire iron and use long screw drivers or whatever for the other pry tools. A valve fishing tool to hold the valve stem in it's hole (while you re-assemble) is very valuable also. I reinstall the opposite side of the tire from the valve stem first, and second do the stem side with the section nearest the stem going on last to keep from pinching the stem out of it's hole. The note about using a little soap and water on the bead/rim to help reseat it is not to be ignored! (Unless you enjoy doing jobs twice.)
Stan(VA).


Follow Ups:




Post a Followup

:
:

: Re: Re: Re: Can I change a rear tire myself?

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Tractor Profile: Allis-Chalmers Model G - by Staff. The first Allis-Chalmers Model G was produced in 1948 in Gasden, Alabama, and was designed for vegetable gardeners, small farms and landscape businesses. It is a small compact tractor that came with a complete line of implements especially tailored for its unique design. It featured a rear-mounted Continental N62 four-cylinder engine with a 2-3/8 x 3-1/2 inch bore and stroke. The rear-mounted engine provided traction for the rear wheels while at the same time gave the tractor operator a gre ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy