|
Farmall & IHC Tractors Discussion Board |
Re: Re: Re: farmall 230 hitch
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Stan(VA). on March 17, 2004 at 20:55:13 from (208.59.157.137):
In Reply to: Re: Re: farmall 230 hitch posted by jim greene on March 17, 2004 at 19:48:38:
From the parts book, the piece that bolts to the tranny is the 'drawbar'. It has two bolts in front and two in back to attach to the tranny. Height in back is somewhat adjustable by using one of two sets of holes. Drawbar is almost a square shape made from maybe 3/8 to 1/2" steel, with ears that stand up verticaly in the back for the hight adjustment bolt positions. It has the standard horizontal drawbar setup on the rear with 6 or 7 holes. In the front it's a little curved with provision for the pin to secure the swinging drawbar. The 'swinging drawbar' is made from C section stamped steel that rides under the back of the drawbar and curves up under the tranny to where it pins at the front of the drawbar mentioned earlier. The 'swinging drawbar hitch plate' is maybe 3/4 to 1" thick flat steel bar that bolt up in the C channel of the swinging drawbar. It has several pairs of holes drilled to allow variable spacing from the tractor to the hitch point. And just to add to the confusion ;) there is also a fast hitch drawbar (a U shapped piece with the two points to plug into the fast hitch), and a fasthitch swinging drawbar that mounts with the drawbar to give about the same functionality as the original setup. If you're going to do heavy drawbar towing (like disking, etc) then I would recommend that you go ahead and switch over to the standard drawbar. I've seen to many worn out fast hitches because of the heavy towing done using the hitch (which replaces the drawbar, instead of having provision to work with a standard drawbar the way most 3 pnt hitches do).
Stan(VA).
Follow Ups:
Home
| Forums
Today's Featured Article -
Tractor Profile: Allis-Chalmers Model G - by Staff. The first Allis-Chalmers Model G was produced in 1948 in Gasden, Alabama, and was designed for vegetable gardeners, small farms and landscape businesses. It is a small compact tractor that came with a complete line of implements especially tailored for its unique design. It featured a rear-mounted Continental N62 four-cylinder engine with a 2-3/8 x 3-1/2 inch bore and stroke. The rear-mounted engine provided traction for the rear wheels while at the same time gave the tractor operator a gre
... [Read Article]
Latest Ad:
Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|
